Nexo PS Series User Manual Download Page 31 | Manualshive

Page: 31 / 82

background image

PS

S

ERIES HARDWARE SETUP PROCEDURE

Page 31/82

7.2 General Description

PS10R2 and PS15R2 incorporate connecting plates (one on PS10R2 and one per side on PS15R2) on
which a comprehensive range of accessories can be mounted.

PS10R2 AND PS15R2 CONNECTING PLATES

There are two families of accessories:



fixed installation accessories, which are designed to be screwed on the connecting plates;



touring accessories, which can be installed or removed with quick connecting systems.

7.2.1 WARNINGS ON PS SERIES ACCESSORIES

WARNING 1T

All PS Accessories are specifically rated in agreement with structural computations.
Never use other accessories when installing PS Series cabinets cabinets than the ones
provided by NEXO: NEXO will decline responsibility over the entire PS Series accessory
range if any component is purchased from different supplier.

WARNING 2

All PS Series accessories have been designed so that cabinets are installed as single
standalone speakers.
PS Series assemblies as shown in figure below are UNSAFE and STRICTLY PROHIBITED.

NO

Oblong holes for Touring Applications Accessories

Tapped holes for Fixed Installation Accessories

«
...
29
30
31
32
33
...
»

Summary of Contents for PS Series



















































































Reviews:

No comments

Related manuals for PS Series

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Origami 4M-006-01

Brand: 4 Moms Pages: 28

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 12

vlt soft starter mcd 500

Brand: Danfoss Pages: 96

Brand: Harpo Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands