background image

 2                                              version 1.0.1 

Dear Customers! 
 

By selecting th

e

 

CB15WPV

, you have decided to use a professional device that guarantees highest quality and 

 

reliability. We would like to thank you very much for your confidence and kindly ask you to read the following 
instructions 

 

carefully 

 

before 

 

installation 

 

and 

 

operation 

 

in 

 

order 

 

to 

 

take 

 

full 

 

advantage 

 

of 

 

all 

 

quality 

 

features 

regarding this product. 

 

 

The lighting flash with an arrowhead symbol, within an equilateral  
triangle is intended to alert the user to the presence of non-insulated  
dangerous voltage within the product’s enclosure that may be of  
sufficient magnitude to constitute a risk of electric shock to persons. 

 

 

The exclamation point within an equilateral triangle is intended to alert  
the user to the presence of important operating and maintenance  
(servicing) instructions in the literature accompanying the appliance. 
 
 

INFORMATION 

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when 
the  equipment  is  operated  in  a  commercial  environment.  This  equipment  generates,  uses,  and  can  radiate 
radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the  instruction  manual,  may  cause 
harmful  interference  to  radio  communications.  Operation  of  this  equipment  in  a  residential  area  is  likely  to 
cause  harmful  interference  in  which  case  the  user  will  be  required  to  correct  the  interference  at  its  own 
expense. 
 

WARNING 

Changes  or  modifications  not  expressly  approved  by  the  manufacturer  could  void  the  user’s  authority  to 
operate the equipment. 
 

CAUTION – To prevent electric shock and risk of the fire hazards 

-Do NOT use power source other than that specified.  
-Do NOT expose this appliance to rain or moisture. 

 
This installation should be made by a qualified service person and should conform to  
all local codes. 
 
 
 
 
 
 

Summary of Contents for CB15WPV





















Reviews: