background image

Page 3 / 10 

 Note 

— If ‘   ‘  ‘ indication appears on a selected s b

menu. 

— If ‘ 

---

 ‘ indication appears on any s b

            (Ex : When SENS-UP is OFF, 3
 

3. LENS

Select the lens and adjust the SETUP s itable to the type of lens.
 

 When DC lens is used. (

 Defa lt)

 
1. Please select the lens mode to DC IRIS.
2. Press the Tact SW to enter the <DC IRIS MENU>.
 
- BRIGHTNESS: adjust the brightness of screen when the environment is 
extremely bright or dark.   
- REACTION: Reaction speed of the sh tter is adj stable. It i
the light condition of  the environment 
 

3.  Save  
     Press SAVE to finish all settings and ret rn to <MAIN MENU>
 

 When MANUAL lens is used. 

1. Please select the lens mode to MANUAL.
2. Press the Tact SW to enter the <MANUAL IRIS MENU>.

-  BRIGHTNESS: same as above
-  REACTION: same as above

 
 
 
 
 
 

4. EXPOSURE

(1) AGC (Auto Gain Control) 

- OFF: Deactivates the AGC f nction.

- LOW: Allows automatic gain control from 0 to 20dB. (
- MIDDLE: Allows automatic gain control from 0 to 30dB.
- HIGH: Allows automatic gain control from 0 to 42dB.

 

 The higher the gain level, the brighter the screen becomes while the higher the noise as well.

 

 

 

indication appears on a selected sub-menu, press the Tact SW to get into a following

‘ indication appears on any sub-menu, it means the function with this mark is deactivated.

UP is OFF, 3-DNR becomes deactivated ‘---‘ )   

Select the lens and adj st the SETUP suitable to the type of lens. 

Default) 

1. Please select the lens mode to DC IRIS. 
2. Press the Tact SW to enter the <DC IRIS MENU>. 

BRIGHTNESS: adj st the brightness of screen when the environment is    

Reaction speed of the shutter is adjustable. It is useful when 

of  the environment keeps changing quickly.  

Press SAVE to finish all settings and return to <MAIN MENU> 

 

1. Please select the lens mode to MANUAL. 
2. Press the Tact SW to enter the <MANUAL IRIS MENU>. 

BRIGHTNESS: same as above 
REACTION: same as above 

OFF: Deactivates the AGC function. 

LOW: Allows a tomatic gain control from 0 to 20dB. (

 Default) 

MIDDLE: Allows a tomatic gain control from 0 to 30dB. 
HIGH: Allows a tomatic gain control from 0 to 42dB. 

higher the gain level, the brighter the screen becomes while the higher the noise as well.

men , press the Tact SW to get into a following 

men , it means the f nction with this mark is deactivated. 

higher the gain level, the brighter the screen becomes while the higher the noise as well. 

Summary of Contents for CB15WPV





















Reviews: