Ness G1 Installation Manual Download | Manualshive

Page: 9 / 50

background image

9

CAMERA

You can pair unlimited number of cameras to your gateway. These cameras need to be either the Indoor or
outdoor Ness IP Z‐Wave Cameras. (101‐803 or 101‐804) Other IP Cameras are not supported.

101‐803

101‐804

NESS 722 Z‐WAVE INDOOR CAMERA

NESS 727 Z‐WAVE OUTDOOR CAMERA

Smart WiFi Setup

This feature allows the IP camera to scan the QR Code from the app to add it to the system.
If you are connecting the IP camera to your WiFi then select this option.

This feature is only supported on the 101‐803 Camera only. (Not supported on the 101‐804).

1. Power up your camera without plugging in the LAN Cable, and wait approx 1‐2
minutes for it to fully power up.

2. Remove the protective plastic cover from the camera lens.

3. Select the option ‘Smart WiFi Setup’. Then press the Next button icon up the
top right.

Note:

Your phone needs to be connected to the WiFi network you are planning to
connect the IP Camera to.

4. When prompted, enter in the WiFi Password to your WiFi Access Point and
press OK.

«
...
7
8
9
10
11
...
»

Summary of Contents for G1



















































Reviews:

No comments

Related manuals for G1

Brand: ICP DAS USA Pages: 33

Brand: Icom Pages: 2

Brand: Icom Pages: 160

Brand: 3onedata Pages: 3

Mediant 1000 MSBG

Brand: AudioCodes Pages: 160

Brand: Star-net Pages: 31

Brand: Yacht Devices Pages: 60

Brand: Fastus Pages: 2

Brand: Gree Pages: 12

VoiceFinder AP-MG3000N

Brand: AddPac Pages: 36

Brand: Adcon Pages: 366

Brand: Alcatel-Lucent Pages: 4

Brand: SAFARI Pages: 8

MediaAccess TG799vn

Brand: Technicolor Pages: 128

Brand: Rosonix Technology Pages: 16

802.11g ADSL 2+ 4-Port Security Gateway HW-D Series

Brand: ZyXEL Communications Pages: 496

Brand: D-Link Pages: 75

ESPRESSObin Ultra

Brand: GlobalScale Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands