Page 15
Activation of the timer command affects all the actuator outputs of the associated
modules: exit 1-exit 2 of the first module, exit 3-exit 4 of the second module and exit 5-
exit 6 of the third module.
The opening or closing of the windows can be set by the parameters P105-P205-P305-
P405-P505-P605.
6.3.5. Sensor priority – Parameter P006
By means of parameter P006, higher priority can be assigned to one of the sensors
(wind-rain-timer) in case events occur simultaneously.
Attention.
In case events occur simultaneously, the unit will follow these priorities:
1. General manual command
2. Single manual command
3. Remote control
4. Sensors
5.
Aeration
6.
Restoration
6.3.6. Exit reset time – Parameters P102, P202, P302, P402, P502, P602
After intervention of the sensors (rain, wind) and the reset time set by parameter P102
– P202 – P302 – P402 – P502 – P602 has passed, the window returns to the previous
scenario.
Caution
.
If you do not want to use this function, leave the parameter P102 – P202 – P302 – P402
– P502 – P602
= 0
With P102 – P202 – P302 – P402 – P502 – P602 = 0, when one or more sensors
intervene the window goes to the position instructed by the sensor with higher priority
and remains there.
6.3.7. Output ventilation time – Parameters P106, P206, P306, P406,
P506 and P606
The Ventilation function is for automatically ventilating the room. To activate this
function, press the F1 and arrow ▲buttons in sequence on the radio remote control.
The window opens for the set time and then closes again automatically, unless other
commands are given. If a rain sensor signal or a manual or radio-controlled command
is given, the ventilation function is interrupted; to restore the function, the button
sequence must be repeated.
The set time also includes the opening time of the actuator.
6.3.8. Other parameters – Parameters P101, P201, P301, P401, P501,
P601, Add, dEL, ReTx, rESE
- The parameter P101 – P201 – P301 – P401 – P501 – P601 is used to set the
work time of the exit.
- The parameter “
Add
” of the menu is used to save one or more channels of the
PIK radio remote control in the station.
Page 16
- The parameter “
dEL
” of the menu is used to delete one or more PIK radio remote
controls saved previously.
- The parameter “
ReTx
” of the menu is used to delete all PIK radio remote controls
from the memory.
- The parameter “
rESE
” of the menu is used to restore the factory-set values
(Default).
6.4.
Saving a PIK radio remote control
This paragraph concerns only the KL_R or KH_R units equipped with PIK radio remote
control.
T
HE CONTROL UNITS LEAVE THE FACTORY WITH THE REMOTE CONTROL ALREADY INSERTED IN
THE MEMORY
;
CARRY OUT THE MEMORIZATION PROCEDURE ONLY IF YOU WANT TO ASSOCIATE
OTHERS
.
The remote electronic control provided with KL_R and KH_R units is equipped with 30
selectable channels. Each command channel is connected to one unit exit.
Opening/closure/stop of each exit can be commanded using arrow ▲/▼ and STOP
buttons.
For more details on the characteristics and operation of the
PIK
radio remote control,
consult the instructions manual provided with the radio remote control itself;
not all the
functions of the radio remote control are listed in this manual.
The KL_R or KH_R station can accept maximum up to 6 PIK radio remote controls.
Memorizing procedure:
- Equip yourself with the radio remote control, checking beforehand that it is
working, has charged batteries and is in good condition.
- Select the “Add” item in the unit menu.
- Press the “OK” button.
- The message “Push” will appear on the display.
- On the PIK radio remote control
(see the instructions provided with the radio
remote control)
, select any channel between CH1 and CH6 and press any one of
the ▲/▼ ARROW or STOP buttons on the PIK for about 1 second.
- The “OK” message will appear on the unit display, indicating that the memorizing
process was successful.
- The radio remote control is now saved and the actuators are controlled by the
respective channels. (CH1=exit 1; CH2=exit 2….. CH6=exitr 6).
In case of full memory “
FULL
” message appears on the display.
In case of remote control not associated “
Err
” message appears on the display.
Repeat the procedure for any other radio remote controls.