Page 7
6. TECHNICAL OPERATING INFORMATION
6.1. General instructions
The control unit is composed of a “mother board” which is set up for insertion of
“expansion module boards”.
The “expansion module” boards differ depending on the control voltage of the motors.
The modules can be for 24V
actuators or 100/240V~ 50/60Hz ones.
The control unit is set up for insertion of a maximum of 3 “expansion modules”. Each
expansion module has 2 exits and can control more actuators; this number has to be
decided on the basis of their nominal absorption. In case of doubts take contact with the
producer.
Caution:
using 24V
actuators chose the unit with the suitable output power.
Model
Number of expansion modules
(Control voltage)
Number of exits
provided for
KH2 – KH2R
1 – (110-240V~ 50/60Hz)
2
KH4 – KH4R
2 – (110-240V~ 50/60Hz)
4
KH6 – KH6R
3 – (110-240V~ 50/60Hz)
6
KL2 – KL2R
1 – (24V
)
2
KL4 – KL4R
2 – (24V
)
4
KL6 – KL6R
3 – (24V
)
6
Each expansion module has inputs for manual open/close controls for each individual
actuator (local command); instead, inputs for all actuators controls (general command)
are placed in the “mother board”. We recommend the use of
n.o
. (normally open) type
interlock switch buttons, see parameter P*07 for associated functions. The
KL..R
and
KH..R
models allow the use of the
PIK
radio remote control with 433.92 MHz proprietary
protocol, as well as manual control.
6.2. Programming
6.2.1. Programming Display and Programming Menu
The following information and instruction are important for the functioning of the
whole system.
A display is installed on the station whit a programming menu for all the station functions.
All the settings of the
PXXX
functional parameters must be made through the keys and
display of the station, changing the preset values
F
[factory-set].
The
OK
key is used to enter the programming menu and confirm the setting of each
individual parameter.
The
+
(plus)
key is used to scroll up through the programming menu or increase the
value of the parameter within the menu.
The
–
(minus)
key is used to scroll down through the programming menu or decrease
the value of the parameter within the menu.
Page 8
The
+
(plus)
and
–
(minus)
keys pressed together are used to exit the programming
menu.
IMPORTANT: the change of some parameters can compromise the
functioning and the desired security level.
(display)
The initial menu is free of any writing when no input is active; otherwise it
shows the activated function with the following messages:
In01
- general Open
In02
- general Close
In11
- actuator 1 Open
In12
- actuator 1 Close
In21
- actuator 2 Open
In22
- actuator 2 Close
In31
- actuator 3 Open
In32
- actuator 3 Close
In41
- actuator 4 Open
In42
- actuator 4 Close
In51
- actuator 5 Open
In52
- actuator 5 Close
In61
- actuator 6 Open
In62
- actuator 6 Close
pk01
- channel 01 of the PIK radio remote control
u Km
- wind speed
r
- rain state
cron
- timed thermostat / timer
Pressing
+
(plus) and – (minus) together it’s displayed the total number of
PIK radio remote control saved in the memory.
-↑ +↓
P001
Wind sensor activation threshold (5 - 50) Km/h F[30]
-↑ +↓
P005
Rain sensor exclusion time (0 - 10) min F[0]
-↑ +↓
P006
Sensor priority (1 - 3) F[1]. Priority can be selected for only one sensor,
where:
1=rain
2=wind, 3=timer
-↑ +↓
P101
Exit 1
work time (10 - 240) s F[60]