Page 13
-↑ +↓
P607
Exit 6
Single manual command functioning mode:
0=half-automatic mode
1=dead-man mode, sensors and remote controls enabled
2= dead-man mode, sensors and remote controls disabled
-↑ +↓
Add
Adds PIK radio remote control channel in the memory
-↑ +↓
chc
Changes the association: PIK radio remote control channel No.
actuator No.
-↑ +↓
dEL
Deletes 1 PIK radio remote control from the memory
-↑ +↓
ReTx
Deletes all PIK radio remote controls from the memory (press twice and
the message “
end
” appears)
-↑ +↓
rESE
Restores the Default values of each parameter F[X] (press twice and the
message “
end
” appears).
6.2.2. Errors table
(display)
The following messages appear on the display in case of error:
FULL
– radio remote control memory full
Err
- the radio remote control is not recognized in either delete or
write
6.3.
Settable functions
6.3.1. Open-close: individual and general manual controls (on the
motherboard) – InXX
For simplicity, from now on the
opening
of the window is associated with forward
movement of the actuator and
closing
of the window is associated with its backward
movement.
The terminal block on the motherboard and expansion modules have manual control
inputs (suitable for voltage-free
n.o.
type buttons) for opening and closing connected
actuators. The operating mode for each output can be selected using parameter P *07.
The general open or general close control affects all outputs and has maximum control
priority. However, it is also conditioned by the mode selected on the individual output: if
P107=0 P 207=1 P307=
2
P407= 1 P507=1 and P607=1, then the general control will
have mode
2
as its operating mode.
Similarly, if P107=0 P 207=
1
P307=0 P407=
1
P507=
1
and P607=0, then the general
control will have mode
1
as its operating mode. When the inputs are activated, the
following message appears on the Display: “
inXX
”.
Page 14
Operation of the individual manual single controls is as follows:
-
0 = Semi-automatic mode
When the
n.o.
contact is closed -
and immediately released
– the input is activated
and the station controls the forward/backward movement of the actuators for the
“output work time” set in parameter P101, P201, P301, P401, P501 and P601.
-
1 = Deadman mode, sensors and radio remote
controls enabled
When the
n.o.
contact is closed, the station controls the forward/back movement of
the actuator until the contact is released. All automatic opening/closing – restore
function – ventilation function controlled by the sensors, remain active (if set). The
radio remote control remains active.
-
2 = Deadman mode, sensors and radio remote
controls not enabled
When the
n.o.
contact is closed, the station controls the forward/back movement of
the actuator until the contact is released. All automatic opening/closing – restore
function – ventilation function controlled by the sensors, are disabled (blocked). The
radio remote control is also disabled.
6.3.2. Rain sensor - Parameters P005, P104, P204, P304, P404, P504,
P604
Upon activation of the rain sensor, the respective message “
r
” appears on the display,
The RAIN input is set up to be connected to a device that detects rain and provides
a voltage-free n.o. contact. The opening/closing action of the window can be set
using the P104-P204-P304-P404-P504-P604 menu.
Supply voltage 24V
for rain sensor
Tension (V)
Maximum Current (mA)
24V
100mA
Please contact Nekos technical office to use rain sensors other than NSR1
In case of rain with the window closed, the window can be reopened by excluding
intervention of the rain sensor for the time set in parameter P005.
Caution
. If unit command comes from the remote control or parameter P*07=0 can be
useful to set a value to force the opening in case of rain. If you do not want to use this
function, leave the parameter P005 = 0.
6.3.3. Wind sensor - Parameters P103, P203, P303, P403, P503, P603
Upon activation of the wind sensor, the respective message appears on the display: “
u
XX
”, where XX is the value of the detected wind speed expressed in Km/h.
The intervention threshold of the wind sensor is set by parameter P001 within the range
5 Km/h
-
50 Km/h.
The opening or closing of the windows can be set by the parameters P103-P203-P303-
P403-P503-P603. Temporary wind gusts do not activate the function.
6.3.4. Cron / Timer input (on main board) - Parameters P105, P205,
P305, P405, P505, P605
A “timer” command input of the voltage-free
n.o.
type is provided on the terminal block.
The command comes from any device that has a voltage-free contact output, such as a
timed thermostat, timer, clock, etc.