background image

Page 6 

2.2. 

Maximum opening according to height of sash 

The actuator stroke is in accordance with the height of the sash and its application. 
Check  that  the  actuator  stroke  does  not  touch  the  profile  of  the  sash  and  that  the 
chain does not exert force on the window frame (Measurements in mm).  

A

TTENTION

.

  For  safety  reasons  the  actuator  should  not  be  assembled  if 

dimensions are inferior to those indicated in the table below. In the event that 
the height of the sash should be lower, call on the manufacturer to check the 
appliance. 

Mode of installation 

Selection of actuator stroke 

240  

360 

Light domes, skylights or vertical top hung windows 
opening outwards with frontal assembly 

400 

550 

Top hung windows opening  outwards  with horizontal 
assembly 

400 

550 

Bottom hung windows 

(motor on frame)

 

400 

550 

Bottom hung windows 

(motor on sash)

 

Consult manufacturer 

3. Technical information about function 

The  chain  actuator  opens  and  closes  the  window  using  a  double  row  steel  chain 
inside  a  sheath.  Movement  is  generated  using  electrical  energy  that  powers  a 
reduction motor controlled by a functional electrical device.  

Windows can be programmed to open and the device allows chain opening at 240 and 
360 mm.  

When  the  window  returns  to  start  position,  that  is  during  closure,  the  stroke-end 
uses  an  electronic  self  regulating  process  with  absorption  of  energy  and  no 
regulation is therefore required.  

The actuator is produced by the factory with the stroke-end for return set at around 
+1  cm  (out  by  1  cm).  This  allows  the  actuator  to  be  assembled  without  electrical 
energy  powering  movement  and  means  that  the  window  remains  closed  after 
assembly.  

The joint between actuator and support brackets is quick, requires no fixing screws  
(

NEKOS 

patent) and allows the actuator to rotate to follow the track of the chain even 

on shorter windows. 

4. Manufacture and applicable standards or regulations 

  The  chain  operated 

series  253  KATO

  actuator  has  been  designed  and 

manufactured  to  open  and  close  top  hung  windows;  bottom  hung  windows; 
dormer windows; light domes and skylights. It has been specifically designed for 
ventilation  and  climate  control  and  any  other  use  is  prohibited  unless  previously 
authorised by the manufacturer.  

Summary of Contents for KATO 253

















Reviews: