background image

Children are strictly prohibited to operate the equipment. 

3.5 Safety Instructions for charger & battery cartridge 

1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating 

instructions for battery charger. 

2. Before using battery charger, please read all instructions and cautionary markings on   

battery charger

  battery

  product and how to use the battery. 

3. CAUTION

 

- The charge can only use GTS rechargeable batteries which has been marked on 

the charger label to reduce risk of injury . Other types of batteries may burst causing personal 

injury and damage. 

4. Do not expose charger to rain or snow. 

5. Do not use an attachment which is not recommended or sold by the battery charger 

manufacturer

it may give rise to a risk of fire, electric shock, or injury to ours. 

6.Pulled by using plug rather than using cord when you want to disconnect the charger to 

reduce risk of damage of the electric plug and cord. 

7. Make sure that cord is not stepped on, tripped over, otherwise it causes unnecessary 

damage. 

8. Do not operate the charger that cord or plug has been damaged and replace them 

immediately. 

9.Do not operate charger if it has got a sharp blow, been dropped or damaged in any way. 

Please take it to a qualified serviceman. 

10. Do not disassemble charger or battery cartridge. Take it to a qualified serviceman when it 

need to be required. Incorrect reassembly may cause a risk of electric shock or fire. 

11. Please switch the machine off to reduce risk of electric shock, unplug charger from outlet 

before attempting any maintenance or cleaning.   

12. The battery charger is not operated by young children or infirm persons without supervision. 

13. If it has been taken too much time to be operated , you should stop operating immediately. It 

may cause a risk of overheating, burn and even an explosion. 

14. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention 

right away. It may result in loss of your eyesight. 

3.6 Additional safety rules for charger & battery cartridge 

1. Do not charge when temperature is BELOW -40°C or ABOVE 40°C. 

2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 

3. Do not allow anything to cover or clog the charger vents. 

4. Always cover the battery terminals when the battery cartridge is not used. 

5. Do not short the battery cartridge: 

(1) Do not touch the terminals with any conductive material. 

(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, 

etc. 

(3) Do not expose battery cartridge to water or rain. A battery short can cause a large current 

flow, overheating, possible burnt and even broken down. 

6. Do not store the tool and Battery Cartridge in locations where the temperature may reach or 

Summary of Contents for CT3656

















Reviews: