background image

Copyright

Copyright © Nedap N.V. All rights reserved. The information in this document is subject to change without

notice, it is not to be reproduced in any way, in whole or in part, without the written consent of Nedap N.V. All

trademarks referenced belong to their respective owners.

Disclaimer

Nedap N.V. has made every effort to ensure the accuracy of the information contained in this document.

However, Nedap N.V. makes no representations or warranties whatsoever whether express or implied as

to the accuracy, correctness, completeness or fit-for-purpose or suitability for the purpose of this product.

You use the products at your own risk. Nedap N.V. excludes any liability to the maximum extent permitted by

applicable law for the damages caused by errors or failures made during the installation or improper use of

this product or by not applying the instructions stated in this document. Nedap N.V. reserves the right to make

improvements or amendments to this document and/or the products described therein at any time without any

notification. The latest version of this document can be found on the Nedap Livestock Management business

portal (www.nedap.com/livestockmanagement-portal). Please download the latest version of this document (by

yourself or reseller) and keep a copy for your own records. This document can be published in various languages

but only the English language version will prevail. Nedap N.V. assumes no responsibility for any errors caused for

the translations into another language.

Warranty and spare parts

Please consult the Nedap products dealer from whom you purchased this product, in regards to the applicable

warranty conditions. This product cannot be used for any other purpose as described in this document. If

the product is not installed according to this document; the warranty provided is not applicable. At the sole

discretion of Nedap N.V., Nedap N.V. may decide to change the conditions of the warranty policy. You agree

that Nedap N.V. is able to compensate you the pro-rata value of the warranty involved rather than replacing

or repairing the product depending on the technical or economical value of the product. Prior to applying the

warranty, please verify if you comply with the warranty conditions of the warranty policy, whether you can

successfully apply for the replacement or repair of a defective part. Parts can only be replaced with original

Nedap parts, otherwise the warranty policy will not be applicable on the product. If the warranty is applicable,

please contact the dealer or send the defective parts to the dealer.

Additional information

For any information or questions regarding the product, please contact your own dealer.

Summary of Contents for VP1007-B



































Reviews: