background image

 

  

   

 

 

WARNING

 

The Nectre 2000 space heater has a primary safety glass fitted in front of the glass door. This safety 
glass is fitted to this appliance to reduce the risk of injury from burns and at no time should this glass 
be permanently removed.

 

For protection of young children or the infirm, a secondary guard is required.

 

The  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given 
supervision or instruction concerning use of the appliance by a person responsible for their  safety. 
Children should be supervised to ensure that they do not play with the appliance.

 

IMPORTANT SAFETY NOTICE

 

 

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

 

 

DO NOT USE OR STORE FLAMMABLE MATERIALS IN OR NEAR THIS APPLIANCE.

 

 

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILST IT IS IN OPERATION.

 

 

CARE MUST BE TAKEN TO ENSURE THAT ANY RETURN AIR REGISTER OR EXHAUST SYSTEM  DOES NOT ADVERSLEY 

AFFECT THE OPERATION OF THE APPLIANCE OR DRAUGHT OF CHIMNEY OR FLUE.

 

 

DO NOT MODIFY THIS APPLIANCE.

 

 

APPLIANCE IS DESIGNED TO OPERATE WITH LUMINOUS FLAMES. MAY EXHIBIT SLIGHT CARBON DEPOSIT. 

 

 

NOTE: A slight smell may be apparent for the first few hours of use. This is due to the heat resistant 

paint  curing.  It  is  recommended  to  open  windows  in  the  room  for  the  first  lighting  of  the  fire.  In  some 
instances,  a  slight  discolouration  may  occur  inside  the  firebox.  This  is  a  normal  condition  and  is  not 
covered by warranty.

 

 

 
 

 

 

 
 

 

 

 
 
 
 
 
 
 
 
 
 
 

 

APPLIANCE IS DESIGNED TO OPERATE WITH LUMINOS FLAMES. 

           MAY EXIBIT SLIGHT CARBON DEPOSIT. 
 

 

SERVICING

 

It is recommended you service your gas fire every 2 years as a minimum.

 

 

CORD REPLACEMENT

 

Electrical cord replacement must be undertaken by qualified and trained personnel only.

 

 

VENTILLATION REQUIREMENTS 

Permanent ventilation of the room where the fire is to be situated is essential while fire is in operation. The 
room must have a minimum cross-sectional area of 40,000sq mm of effective ventilation. 

 

INSTALLATION NOTICE

 

 

The installation of this appliance is only to be carried out by an authorised person in accordance 

with the 

Manufacturer’s Instructions, local gas fitting regulations, AS/NZS5601.1-2013 installation code 

for gas burning appliances and any other relevant statutory regulations.

 

 

In all cases the installation of this appliance shall meet the requirements as set out in 

AS/NZS5601.1-2013.

 

 

Do not install in a fireplace as a Type 1 installation.

 

 

Not intended as a fireplace insert. 

 

Summary of Contents for 2000


















Reviews: