background image

 

17 

 

 
 
 

 

 

GLEN DIMPLEX AUSTRALIA PTY LTD 

ABN 69 118 275 460

 

Head Office/Factory/Showroom

 

1340 Ferntree Gully Rd.

 

Scoresby Vic 3179

 

Ph: (03) 8706 2000 Fax: (03) 8706 2001

 

E-mail[email protected] 

Richmond - VIC Showroom

 

300 Swan St.

 

Richmond Vic 3121

 

Ph: (03) 9428 4443 Fax: (03) 9428 4445

 

Dandenong - VIC Showroom  

3/328 South Gippsland Highway, Dandenong South Vic 3164

 

Ph: (03) 9702 7853

 

E-mail[email protected]

 

Geelong - VIC Showroom

 

1/2A Gordon Avenue. Geelong West Vic 3218 Ph/Fax: 5229 0844

 

E-mail[email protected]

 

Sydney - NSW Showroom

 

546 Pacific Highway.

 

Chatswood NSW 2067

 

Ph: (02) 8905 0189 Fax: (02) 8905 0192

 

E-mail[email protected]

 

Miranda - NSW Showroom

 

36 Kareena Rd.

 

Miranda NSW 2228

 

Ph: (02) 8513 6202  Fax: (02) 9520  1974

 

E-mail:  [email protected]

 

Adelaide - SA Showroom

 

173 -175 Magill Rd.

 

Norwood SA 5067

 

Ph: (08) 8132 0371 Fax: (08) 8132 1687

 

E-mail[email protected]

 

 

Milton - QLD Showroom 

 

46 Douglas St,

 

Milton QLD 4064

 

Ph: (07) 3368 2011

 

Perth 

– WA Showroom  

47-53 McDonald St East, Osborne Park WA 6017

 

Ph: (08) 9444 9900 Fax: (08) 9444 9800

 

Fyshwick 

– ACT Showroom

 

88 Wollongong St,

 

Fyshwick ACT 2609

 

Ph: (02) 6280  5522

 

Ulverstone 

– TAS Showroom

 

31A Victoria St, Ulverstone TAS  7315

 

Ph: (03) 6425  4440 

Summary of Contents for 2000


















Reviews: