Necta Samba Top, Installation Operation & Maintenance

Page: 39 / 76

© by N&W GLOBAL VENDING S.p.A.
33
12 2008 3335 00
E
nErgy saving
2 power off time bands can be programmed on a weekly
basis. The days of the week are identified by a progres -
sive number (1=Monday, 2=Tuesday etc.).
The same range can not include the days of different
weeks.
If you should set up overlapping time bands by mistake,
the machine will remain on for the shorter period.
If you wish to set up the Service interruption bands to
power on the machine from 7.00 a.m. to 10.00 p.m. on
the days of the week and power it off on Saturdays and
on Sundays, please set up the bands by means of the
corresponding menu, as it is shown by the following
table.
Day 1 2 3 4 5 6 7
Band 1
start 00.00 00.00 00.00 00.00 00.00 00.00 00.00
end 07.00 07.00 07.00 07.00 07.00 23.59 23.59
Band 2
start 22.00 22.00 22.00 22.00 22.00 00.00 00.00
end 23.59 23.59 23.59 23.59 23.59 00.00 00.00
When the “Energy saving” time band has tripped, the
illumination of the glassfront will remain active and the
display show the “Service Interruption” message.
M
achinE lEd out of sErvicE
Use this function to define whether to turn on or off the
illumination of glass front when the machine is out of
service or the “Energy saving” time band has tripped.
M
achinE sErial nuMbEr
Use this function to change the “machine code”.
The “machine code” is an 8-digit numeric code identify -
ing the machine (default 00000000)
P
rograMMing thE oPErator codE
Use this function to change the 6-digit numeric code
identifying groups of machines (default 00000000).
l
ocation codE
Use this function to change the 6-digit numeric
code identifying the location of the machine (default
00000000).
i
nstallation datE
Use this function to store the current system date as the
installation date.
The date is printed at the time of rolling out statistics.
M
astEr
/s
lavE
The control system of the machine is arranged for bank
connection with other automatic vending machines by
using special kits.
This will enable the operator to use one single payment
system for several machines.
Even if you can use the machine in the master and slave
function, it is recommended to use the snack machine
as a master to make use of the central keyboard and to
open the doors more easily.
The master/slave function is not enabled by default.
To enable it, define the master machine and the slave
machine in the software of the master machine and in
the software of the slave machine.
The payment system of the slave machine shall always
be defined as a “validator”.
In case of power failure, both machines will display the
“communication failure” message.
sEt uP
Use this function to define whether the machine is
a “Master”, i.e. controlling the second machine, or a
“Slave”, i.e. controlled by the other machine.
slavE PricE holding
Enable this function is the machine is configured as a
“slave” and an executive payment system is set up on
the master in the “price holding” mode.
virtual PricE rEturn
Use this function if you do not wish to cash the price
of the second selection if the second dispensing cycle
of a virtual selection should fail (only if MDB payment
systems or validators are in use). For the other payment
systems, you can establish whether to return the whole
amount or not..
MinislavE rEsEt
Use this function to restore the default values of a
“Slave”.
slavE inforMation disPlay
Use this function to display the information on the slave
machine (software release, number of trays, number of
dispensing cycles, locked motors...)