background image

© by NECTA VENDING SOLUTIONS SpA

01 10 126-03

48

If a single column, a plastic diaphragm, hooked to the
upper side of the column.
In order to correctly load the column, do as follows:

- release the diaphragm by lifting it by its grip;

- load some bottles in the back row (to half height) and

position the diaphragm against it;

- load the bottles in the front row;

- complete loading of the back row and re-hook the

diaphragm .

- complete loading of the column.

After completely loading the machine:

- close the retaining gate:

- after all loading operations make a test selection for

each product.

All loading operations must be carried out as quickly as
possible, to limit as much as possible the increase of
temperature inside the refrigerated box and therefore
power consumption.

Fig. 13

1 - Diaphragm
2 - Diaphragm grip
3 - Diaphragm hook

TEMPERATURE CONTROL

The thermostat is initially adjusted so that a temperature of
+1.5°C is maintained in the lower portion of the refrigerated
box (containing bottles and cans which will be sold first).
The thermostat is located next to the refrigerating unit (see
Fig. 5).
To change temperature, turn the thermostat knob keeping
in mind that the temperature is approximately:

position “7”

= + 1,5°C

position “1”

= + 5°C

position “OFF”

= Switched off

RELEASING A COLUMN

It may occur that, for any reason, the products are jammed
in the dispensing area.
In this case, to restore the full functionality of the jammed
column, do as follows:

- manually empty the concerned column, being sure that

the rotor area is clear;

- move minidip 6 on the control card (see Fig. 14) to

position ON.

Fig. 14

1 - Control board
2 - Minidip

- close the door and wait a few seconds to allow the

motor to reach the correct position;

- open the door and move minidip 6 back to position OFF

- reload the column and close the machine, then check

that the corresponding selection is working correctly.

Summary of Contents for Zeta CB Series









































Reviews: