NEC VisuaLink 128 Quick Installation Manual Download Page 42 | Manualshive

Page: 42 / 62

background image

Page 5-2

NDA-24232 Issue 2.0

Chapter 5

VisuaLink 128/384 Quick Installation Guide

4. Using a Phillips screwdriver, remove the four (4) screws that attach the cover

panel to the housing of the VL 128. The four screws are located on the bottom
of the VL 128.

Note:

While in this position, place the Upgrade Label supplied with the
Upgrade Kit at the position shown in the illustration below. The label
shows the VisuaLink 128 has been upgraded to a VisuaLink 384. Do not
block the air grid when placing label.

5. Using a Phillips screwdriver, remove the three (3) screws that attach the cover

panel to the housing of the VL 128. The four screws are located on the rear of
the VL 128.

6. Slid the cover towards the rear of the chassis, to remove. Using a Phillips

screwdriver remove the four (4) screws from the rear panel.

Screws

Screws

Upgrade

Lable

Upgrade Label

Screws

Screw

Screws

«
...
40
41
42
43
44
...
»

Summary of Contents for VisuaLink 128































































Reviews:

No comments

Related manuals for VisuaLink 128

Brand: Saito Pages: 90

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: M-Audio Pages: 12

COMPETITION ProZ4-80

Brand: µ-Dimension Pages: 7

SB3.0-1SP-US-40

Brand: SMA Pages: 17

Brand: ICT Pages: 11

Brand: Elko Pages: 18

EtherCAT 390 Series

Brand: MKS Pages: 42

Brand: auna Pages: 68

Brand: Sharp Pages: 38

Brand: Sharp Pages: 54

KEX-M9537ZT-02/UC

Brand: Pioneer Pages: 8

KEH-P4020 - Radio / Cassette Player

Brand: Pioneer Pages: 6

Brand: Pioneer Pages: 6

Brand: Pioneer Pages: 6

Brand: Pioneer Pages: 6

Brand: Pioneer Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands