NEC VisuaLink 128 Quick Installation Manual Download Page 39 | Manualshive

Page: 39 / 62

background image

NDA-24232 Revision 1.0

Page 4-11

VisuaLink 128/384 Quick Installation Guide

Chapter 4

25.

Verify that all the equipment plugged into the
power strip are turned to the ON position. The
VisuaLink 128/384, camera and monitor have
their own power switches. If a device appears to
be still in the OFF position, check the power
connection from the Power Strip to the device.
The NT1 does not have a power switch. The
green LED on the front of the NT1 is an indication
the unit is powered ON.

Note: Make sure the monitor is selected for

Video 1.

26.

When the VisuaLink 128/384 is powered ON, a
display of the NEC America, Inc. logo, VisuaLink
name, POWERING UP and version number will
be displayed on the monitor.

STEP

ACTION

DRAWING

POWER

HEADSET

POWERLINE

B1 B2

Powering Up

22.99.99

VisuaLink

America, Inc.

«
...
37
38
39
40
41
...
»

Summary of Contents for VisuaLink 128































































Reviews:

No comments

Related manuals for VisuaLink 128

Brand: Handicare Pages: 56

Brand: iDance Pages: 25

Brand: Yealink Pages: 8

Brand: Panasonic Pages: 16

Brand: Polycom Pages: 36

Brand: Clatronic Pages: 38

Brand: Innovative Technology Pages: 14

Brand: Jensen Pages: 3

ProAudio ARX7570z

Brand: Clarion Pages: 29

Brand: Poly Pages: 16

Brand: D-Link Pages: 10

WX-C1011 Series

Brand: Panasonic Pages: 18

WGAV120 - VIDEO TRANSMISSION

Brand: Panasonic Pages: 40

VoiceSonic KX-NT700

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

WXC3010 - CENTER MODULE - MULTI LANGUAGE

Brand: Panasonic Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands