manualshive.com logo in svg

NEC VERSA DAYLITE E120, User Manual

Share
Download
NEC VERSA DAYLITE E120 User Manual Download Page 84

5-12   Adding Expansion Devices

Memory Module

System memory is upgradeable from 256 MB to 768 MB. The NEC Versa E120
DayLite has one 64-bit memory slot for a 144-pin SO-DIMM (Small Outline Dual
Inline Memory Module). The slot supports a 128-MB, 256-MB, or 512-MB (when
available) SDRAM module. The memory slot is located on the bottom of your
notebook. See the following procedures to upgrade system memory.

Installing a Memory Module

Follow these steps to upgrade the system memory.

1. 

Power off the system, disconnect AC power, and disconnect any peripheral
devices.

If installed, remove the optional secondary battery (see “Secondary Battery” later
in this chapter).

2. 

Locate the screw securing the memory bay cover to the bottom of the notebook.

Memory bay cover

A – Memory Bay Cover

B – Screw

3. 

Remove the screw and lift off the memory bay cover.

Summary of Contents for VERSA DAYLITE E120


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands