manualshive.com logo in svg

NEC VERSA DAYLITE E120, User Manual

Share
Download
NEC VERSA DAYLITE E120 User Manual Download Page 30

Getting Started   2-5

Connecting the AC Adapter

Note   

The AC power cable type that your system uses depends on the country

where you are using it. Contact the local dealer to purchase the correct power cable if it
differs from the one provided.

Connect the AC adapter as follows.

1. 

Connect the AC adapter cable to the power port at the rear of your NEC Versa
notebook.

2. 

Plug one end of the AC power cable into the AC adapter and the other end into a
properly grounded 120- or 240-volt, 50- or 60-Hz wall outlet.

Connecting the AC adapter

Do not cover or place objects on the AC adapter. Keeping the

adapter clear of objects lets the adapter cool properly during use.

Only use the AC adapter that comes with your NEC Versa E120 DayLite. Although other
adapters look similar, using them can damage your system.

Summary of Contents for VERSA DAYLITE E120


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands