NEC UPD789026 Series User Manual Download

Page: 170 / 213

CHAPTER 11 STANDBY FUNCTION

User's Manual U11919EJ3V0UM00

170

(2)

Releasing HALT mode

The HALT mode can be released by the following three types of sources:

(a) Releasing by unmasked interrupt request

The HALT mode is released by an unmasked interrupt request. In this case, if the interrupt request is

enabled to be accepted, vectored interrupt processing is performed. If the interrupt is disabled, the

instruction at the next address is executed.

Figure 11-2. Releasing HALT Mode by Interrupt

HALT

Instruction

Standby

Release Signal

Wait

HALT Mode

Operation

Mode

Operation Mode

Clock

Oscillation

Remarks 1. The broken line indicates the case where the interrupt request that has released the

standby mode is accepted.

2. The wait time is as follows:

•

When vectored interrupt processing is performed

: 9 to 10 clocks

•

When vectored interrupt processing is not performed : 1 to 2 clocks

(b) Releasing by non-maskable interrupt request

The HALT mode is released regardless of whether the interrupt is enabled or disabled, and vectored

interrupt processing is performed.

www.DataSheet4U.com

Summary of Contents for UPD789026 Series






















































































































































































































Search results

Summary of Contents for UPD789026 Series

Reviews:

Related manuals for UPD789026 Series

Brands by name

Popular brands

NEC UPD789026 Series, User Manual

Search results

Summary of Contents for UPD789026 Series

Reviews:

Related manuals for UPD789026 Series

Brands by name

Popular brands