NEC Express 320Lc User Manual Download Page 84 | Manualshive

Page: 84 / 145

NEC Express 320Lc User Manual Download Page 84

4-40

Windows Setup

3. When RDR is successfully configured, the following two pop-up messages appear.

On the “Warning” pop-up, click [OK], and on the “System Restart Warning” pop-up, click
[Yes].

IMPORTANT:

Clicking [Yes] on the “System Restart Warning” pop-up will restart the system in 2
minutes.

If the pop-up appears multiple times, follow the instruction to restart the system.

4. The following pop-up appears, and the system will be restarted in two minutes:

5. After the system is restarted, mount a disk to set dual disk configuration in Slot 1 of the PCI

module (Group 2).

IMPORTANT:

Mount a new or physically formatted disk which has the same capacity as the mirrored
disk (disk in Slot1 of PCI module (Group1)). (About formatting disks physically, see
“System Configuration” – “SCSI BIOS~Fast!UTIL~” in the separate volume of User’s
Guide to perform “Low-Level Format” on the SCSI Disk Utility.)

«
...
82
83
84
85
86
...
»

Summary of Contents for Express 320Lc


















































































































































Reviews:

No comments