NEC Express 320Lc User Manual Download Page 129

Page: 129 / 145

6-10

Troubleshooting

Status emb-82559 10/100 Enet Adapter

Status emb-82544GC Copper Gigabit Adapter

Status AA-U51500 10/100 Enet Adapter (100BASE-TX)

Status AA-U57000 Fiber Gigabit Adapter (1000 BASE-SX)

NEC 8490 XT Copper Gigabit Adapter (1000 BASE-T)

You will then see the dialog box on the right of this paragraph. This is because one of two
teamed adapters constituting dual configuration is removed.

Click [Yes], to remove the adapter from Team.

Remove the other adapter in the same way.

Status emb-82559 10/100 Enet Adapter

Status emb-82544GC Copper Gigabit Adapter

Status AA-U51500 10/100 Enet Adapter (100BASE-TX)

Status AA-U57000 Fiber Gigabit Adapter (1000 BASE-SX)

NEC 8490 XT Copper Gigabit Adapter (1000 BASE-T)

4) Right click [Team #1:Adaptive Fault Tolerance Mode] and select [Remove].

Summary of Contents for Express 320Lc


















































































































































Search results

Summary of Contents for Express 320Lc

Reviews:

NEC Express 320Lc, User Manual, Page: 129 / 145

Search results

Summary of Contents for Express 320Lc

Reviews: