manualshive.com logo in svg

NEC Aspila Topaz, Programming Manual

Share
Download
NEC Aspila Topaz Programming Manual Download Page 96

88

Programming Manual

Program 14: Trunk Basic Setup

14-02: Analogue Trunk Data Setup 

IN

SA

SB

COPY

Input Data(Cont’d)

Prog. No.

Item

Input data

Default

Related

Program

14-02-09

Busy Tone Detection

0 : Disable
1 : Enable

0

14-02-10

Caller-ID

Enable or Disable a trunk’s ability to receive
Caller ID information

0 : Disable
1 : Enable

0

14-02-11

Next Trunk in Rotary if No Dial Tone

Use this option to enable/disable the system’s
ability to skip over a trunk if dial tone is not
detected. This option pertains to calls placed using
Loop Keys, Speed Dial, ARS, Last Number Redial
or Save Number dialed. It does not pertain to line
key or Direct Trunk Access calls.

0 : Disable
1 : Enable

0

14-02-12

Detect Network Disconnect Signal

0 : Disable
1 : Enable

0

14-02-13

Trunk-to-Trunk Limitation

0 : Disable
1 : Enable

0

14-02-14

Loop Start/Ground Start

0 : Loop Start
1 : Ground Start

0

14-02-15

-Not Used-

-

-

-

14-02-16

Caller-ID Type for Analogue Trunk

0 : FSK
1 : DTMF

0

Conditions

None

Feature Cross Reference

‹

 

None

Telephone Programming Instructions

To enter data for Program 14-02(Analogue Trunk Data Setup):

1

. Enter the programming mode.

2. Enter 14 02

3. Enter the number of the item you want to program.

4. Select the Trunk port number to programmed by pressing the FLASH or the VOLUME

▲

 or VOLUME

▼

 keys.

5. Enter data for the item you se HOLD.
6. Enter data for the next item in the program.

OR
Press DC once to enter a new item number.
OR
Press DC until you’ve exited that series’s programming section.

14-02-01 Trunk1

DP/DTMF            1

14-02-xx Trunkxx

xxxxx

Summary of Contents for Aspila Topaz







































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands