NEC Aspila Topaz Programming Manual Download Page 103

Page: 103 / 390

Programming Manual

Program 14: Trunk Basic Setup

14-08: Music on Hold Source for Trunks

SA
SB

COPY

Description

Use

Program 14-08 : Music on Hold Source for Trunks

to define a trunk’s Music on Hold source as either the

ACI or BGM port.

Note:

If ACI is selected as the source in Item 1, the port number for the source must be selected in Item 2.

Input Data

Trunk Port Number

1-51

Prog. No.

Item

Input Data

Default

14-08-01

MOH Type
Select a trunk’s
Music on Hold
source.

0 : Internal synthesized MOH
1 : A customer-provided source connected to BGM port.
2 : A customer-provided source connected to ACI port.

14-08-02

Source Port
Number for
MOH

0-6
If the MOH type is “2”, the source port number is 0-6.

Conditions

None

Feature Cross Reference

Music on Hold

Telephone Programming Instructions

To enter data for Program 14-08(Music on Hold Source for Trunks):

. Enter the programming mode.

2. Enter 14 08

3. Enter the number of the item you want to program.

4. Select the Trunk port number to programmed by pressing the FLASH or the VOLUME

▲

or VOLUME

▼

keys.

5. Enter data for the item you se HOLD.
6. Enter data for the next item in the program.

OR
Press DC once to enter a new item number.
OR
Press DC until you’ve exited that series’s programming section.

14-08-01 Trunk1

MOH Type 1

14-08-xx Trunkxx

xxxxx

Summary of Contents for Aspila Topaz







































































































































































































































































































































































































Search results

Summary of Contents for Aspila Topaz

Reviews:

Brands by name

Popular brands

NEC Aspila Topaz, Programming Manual

Search results

Summary of Contents for Aspila Topaz

Reviews:

Brands by name

Popular brands