manualshive.com logo in svg

NEC Aspila Topaz, Programming Manual

Share
Download
NEC Aspila Topaz Programming Manual Download Page 385

377

Program92: Copy Program

92-01: Copy Command

Programming Manual

SA
SB

IN

Description

Use 

Program 92-01 : Copy Program 

to copy the data for one program to another keyset, port, group, etc. Refer to

the following charts to see which programs which can be copied.

Input Data

Program Number

xx-xx

Prog.No.

Item

Input Data

92-01-01

Source Number

Enter the extension, trunk, group, etc.. from
which the data will be copied.

92-01-02

Destination Number (From)

Enter the first extension, trunk, group, etc.
number to which the information is to be
copied.

92-01-03

Destination Number (To)

Enter the last extension, trunk, group, etc.
number to which the information is to be
copied. If the information is only be copied to
one extension, trunk, group, etc., enter the
information entered in the Destination Number
(From) entry.

•

 In case of Trunk Base …

.

  Trunk Port Number 1-51

• In case of Trunk Group Base….

  Trunk Group Number 1-25

• In case of Extension Base….

Extension Number (Up to 4 digits)

• In case of Department Group Base….

Department Group Number 1-32

• In case of DSS….

DSS Console Number 1-9

Note) Copy Program is applicable only for the following programs

.

1.

 

Trunk Port Base

Prog.No.

Program Name

Note

14-01

Trunk Basic Data Setup

Copy all data except Trunk Name (

14-01-01

)

14-02

Analogue Trunk Data Setup

14-04

Behind PBX Setup

14-08

Music on Hold Source for Trunks

14-09

Conversation Recording Destination for Trunk

21-03

Trunk Group Routing for Trunks

21-12

ISDN Calling Party Number Setup for Trunk

22-02

Incoming Service Type Setup

22-03

Trunk Ring Tone Setup

22-05

IRG Assignment for Normal Ring Trunk

22-08

Second IRG Setup for unanswered DIL / IRG

31-05

Incoming Ring Tone Audible on External
Speaker

Summary of Contents for Aspila Topaz







































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands