manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 35 / 36

Share
Download
Neat INKA Technical Handbook Download Page 35

 

INKA, IOR, REPO & LINK 

3.7 Technical Alarms 

 

3.7.1  Radio Test Alarm 

 
To let the alarm receiver know that the unit is working, INKA, IOR and REPO can send test alarms to 
the alarm receiver at regular intervals. By default this function is turned off. Selecting an interval 
between 1 hour and 255 hours turns the function on. Interval time zero (0) hours means that the 
function is turned off. 
 
The 

test alarm interval 

parameter is found in the 

miscellaneous

 section under the 

preferences 

tab in 

IOR Programmer. 
 

INKA 
IOR 
REPO 

Deactivate the test alarm function 

Enter the value 0 in text box 305 

 

INKA 
IOR 
REPO 

Activate the test alarm function and set 
the test alarm interval. 

Enter the desired time (in hours) in text 
box 305 

 
Please note that no radio test alarms are sent in 

power save mode

, see section 3.5. 

 

 

3.7.2  Battery Alarm: INKA, IOR and REPO 

 
INKA, IOR and REPO can be configured to send a 

battery alarm 

when the battery voltage is too low.  

 
The reason for the alarm can be 
 

•

 

The batteries are getting old and must be replaced 

•

 

The AC/DC adapter is not connected and the unit has been  
battery-powered for a long time (IOR and REPO) 

 
The battery voltage is continuously supervised. If the battery voltage is too low, a battery alarm is sent 
every day until the batteries are replaced. The limit for low battery voltage is 2.6 V in INKA and 3.5 V 
in IOR and REPO. 
 
Please note that no battery alarms are sent in 

power save mode

, see section 3.5. 

 
The 

battery alarm 

parameter is found in the 

miscellaneous

 section under the 

preferences 

tab in IOR 

Programmer. 
 

INKA 
IOR 
REPO 

Activate the 

battery alarm

 function 

Select “Yes/Function on” in list box 302 

 

INKA 
IOR 
REPO 

Deactivate the 

battery alarm

 function 

Select “No/Function off” in list box 302 

 
 
 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

35

 

Summary of Contents for INKA





































Reviews:

No comments