manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 34 / 36

Share
Download
Neat INKA Technical Handbook Download Page 34

 

INKA, IOR, REPO & LINK 

3.5 Power Mode 

 
For longer battery life, INKA and IOR can be configured to go into 

power save mode

 when the AC/DC 

adapter is not connected, and when mains power is lost.  
 
Power save mode is only intended for supervision of wired inputs 1-3. Inputs 4 and 5 are not available 
for use, and no radio messages can be received in power save mode.  
 
Please note that no battery alarms or radio test alarms are sent in power save mode.  
 
When running on mains power with the AC/DC adapter connected, INKA and IOR are always in 
normal power mode with all functionality enabled. REPO and LINK are always in normal power mode. 
 
The 

power mode 

parameter is found in the 

miscellaneous

 section under the 

preferences 

tab in IOR 

Programmer. 
 

INKA 
IOR 

Enable 

power save mode

 

Select “Yes/Function in” in list box 301 

 

INKA 
IOR 

Disable 

power save mode

 

Select “No/Function off” in list box 301 

 
See section 2.2.8 for jumper configuration of the power mode. 
 
 

3.6 Battery Charge Duration 

 
IOR, REPO and LINK are equipped with a rechargeable battery for power back-up in case of AC 
power failure. When one minute has passed after the power to the unit is turned on, the unit starts to 
charge the back-up battery. The duration of the charging is configurable.  
 
The 

battery charge duration 

parameter is found in the 

miscellaneous

 section under the 

preferences 

tab in IOR Programmer. 
 

IOR 
REPO 
LINK 

Configure the battery charge duration 

Enter the desired time (in hours) in text 
box 306 

 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

34

 

Summary of Contents for INKA





































Reviews:

No comments