manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 26 / 36

Share
Download
Neat INKA Technical Handbook Download Page 26

 

INKA, IOR, REPO & LINK 

3.3.3  Relay Action when Radio Message is Received 

 
The relay action can also be configured individually for each of the radio positions 1-8. 
 

IOR 
REPO 
LINK 

Configure the output relay to remain 
unchanged when a radio message is 
received in position 1…8 

Select “None” in list box 121…128 

 

IOR 
REPO 
LINK 

Configure the output relay to switch to the

 

ON

 position hen a radio message is 

received in position 1…8 

Select “Relay on” in list box 121…128 

 

IOR 
REPO 
LINK 

Configure the output relay to switch to the 

OFF

 position hen a radio message is 

received in position 1…8 

Select “Relay off” in list box 121…128 

 

IOR 
REPO 
LINK 

Configure the output relay to change state 
hen a radio message is received in 
position 1…8 

Select “Toggle relay” in list box 121…128 

 

IOR 
REPO 
LINK 

Configure the output relay to switch 

ON

, 

and then 

OFF

 hen a radio message is 

received in position 1…8 

Select “Pulse relay” in list box 121…128 

 
It is possible to configure the relay action when a radio message with the 

fixed input

 ID code is 

received.  
 

IOR 

REPO 

LINK 

Configure the behavior of the output relay 
when a radio message is received with 
the 

fixed input 

ID code 

Select “None”, “Relay on”, “Relay off”, 
Toggle relay” or “Pulse relay” in list box 
129 

 
When the unit is configured to receive all radio ID codes, the relay action is configured separately for 
received radio messages that have an ID code that is not pre-programmed in the unit. 
 

IOR 

REPO 

LINK 

Configure the behavior of the output relay 
when a radio message is received that 
does not have a pre-programmed ID code 

Select “None”, “Relay on”, “Relay off”, 
Toggle relay” or “Pulse relay” in list box 
130 

 
See section 2.2.7 for jumper configuration of the relay action (output mode). 
 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

26

 

Summary of Contents for INKA





































Reviews:

No comments