manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 29 / 36

Share
Download
Neat INKA Technical Handbook Download Page 29

 

INKA, IOR, REPO & LINK 

 

IOR 
REPO 

Configure the unit to transmit a radio 
message using the ID code of the 
received message when a radio message 
is received in position 1…8 

Select “Send same” in list box 131…138 

 

IOR 
REPO 

Configure the unit to transmit a radio 
alarm using the ID code of the received 
message when a radio message is 
received with the 

fixed input 

ID code 

Select “Send same” in list box 139 

 

IOR 
REPO 

Configure the unit to transmit a radio 
alarm using the ID code of the received 
message when a radio message is 
received that does not have a pre-
programmed ID code 

Select “Send same” in list box 140 

 
 

3.4.2  Alarm Type for Transmitted Alarm 

 
The alarm type in transmitted alarms can be configured individually for each wired input and for each 
radio position. By default, the special alarm type 

No alarm type 

is chosen. This means that the home 

care phone NEO will determine the alarm type depending on radio position used in NEO.  
 
If any other alarm type than 

No alarm type

 is chosen, then the home care will use the alarm type 

configured in the INKA, IOR or REPO. Any alarm type in the list can be chosen for transmitted alarms. 
Each alarm type has its own meaning, but it is up to the user that configures the unit to make sure that 
the correct alarm type is used. 
 
When input 4 is configured as 

analog sample

, choose alarm type 

measurement data 

for input 1. See 

section 3.2.2 for a description of 

analog sample 

mode. Likewise, when input 5 is configured as 

analog 

sample

, choose alarm type 

measurement data 

for input 2. 

 

When configuring alarm type for transmitted radio alarms trigged by a received radio message, it is 
also possible to choose the alarm type 

transparent

. This means that the alarm type of the transmitted 

alarm will be the same as the alarm type of the received message. 

 

The alarm type for transmitted alarms when a wired input is trigged is configured in the fields of the 
column 

alarm type 

under the 

wired input 

tab. 

 

INKA 
IOR 

Configure alarm type for transmitted alarm 
when wired input 1…5 is trigged 

Select alarm type from the list in list box 
241...245 

 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

29

 

Summary of Contents for INKA





































Reviews:

No comments