manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 11 / 36

Share
Download
Neat INKA Technical Handbook Download Page 11

 

INKA, IOR, REPO & LINK 

1.8 Inputs: INKA and IOR 

 
Connect wired sensors to the connector marked IN on the bottom side of the unit, see section 1.2.1-
1.2.2.  
 
Up to 5 alarm sensors can be connected to the same INKA or IOR unit. The first sensor is connected 
between pin 3 and 8 in the input connector, the second sensor is connected between pin 4 and 8, the 
third between pin 5 and 8, the fourth between pin 6 and 8 and the fifth sensor is connected between 
pin 7 and 8 in the input connector. See image below. 
 

 

 
 

 

 
Note that inputs 4 and 5 are not available when running INKA or IOR on batteries in 

power save 

mode

, see section 3.5. 

 
The connected alarm sensors may be powered from INKA and IOR. The unregulated voltage from the 
AC/DC-adapter is supplied between pin 1 and pin 8 in the input connector. With the standard AC/DC-
adapter from NEAT, this voltage is 5-9V

DC

. A total of 250 mA may be drawn from pin 1 and 8. A 

regulated voltage of 3 V

DC

 is supplied between pin 2 and pin 8 in the input connector. A total of 50 mA 

may be drawn from pin 2 and 8. 
 

 

 
 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

11

 

Summary of Contents for INKA





































Reviews:

No comments