background image

7

About the Boiler

2.1    Description of the Boiler

The Navien NFC-H boiler is available in 2 models: 
NFC-250/175H and NFC-250/200H.

The main features are as follows:

 

Ɣ

Power Interruption: When the power is restored 
after a power failure, the boiler will automatically 
start and return to normal operation. A manual 
reset is not required.

 

Ɣ

Freeze Protection: A sensor inside the boiler 
automatically detects the temperature and, 
if necessary, initiates a safety heating cycle to 
prevent internal equipment damage due to 
freezing temperatures.

 

Ɣ

Short-Circuit Protection: Any short-circuit 
occurring in the boiler’s electrical circuit 
immediately blows the internal glass fuses and 
automatically cuts off the gas supply.

 

Ɣ

Lightning Protection: Each boiler is specially 
grounded, both internally and externally, to 
protect against lightning strikes.

 

Ɣ

Carbon Monoxide Protection: The boiler is 
designed to maintain a safe air-to-gas ratio and 
combustion rate. This function is continuously 
monitored by the boiler’s combustion controls.

 

Ɣ

Auto Fan Detection: The rotation of the fan is 
automatically detected and controlled. Fan failure 
will stop the operation of the boiler.

 

Ɣ

Boiling Prevention: Excessive temperatures will 
automatically stop the boiler.

2.2    Parts of the Boiler

2.2.1    Front View

Exhaust  
Gas Vent

Combustion  

Air Intake

2.2.2    Bottom View

14.6” (370 mm)

2.6” (67 mm)

9.7” (247 mm) 

5.2” (131 mm)

A

D E

17.3”

(440 mm)

8.5” (215 mm)

10.6“ (269 mm)

3.3”

(85 mm)

2”

(53 mm)

B

C

F

G

5.4”

(136.6 mm)

5.4”

(136.6 mm)

3.4”

(87 mm)

#

Description

A

Heating Supply

B

Hot Water Outlet (DHW)

C

Cold Water Inlet (DHW)

D

Auto Feeder Inlet (Make-up Water)

E

Heating Return

F

Gas Connection

G

Condensate Outlet

2.    About the Boiler

Summary of Contents for NFC-250/200H






























Reviews: