background image

11

Operating the Boiler

2.  Rotate the Command dial (

) to the right to 

select the DHW temperature.

3.  Press the Command dial (

) to select the DHW 

temperature (

). The highlighted section will 

flash.

4.  Rotate the Command dial (

) to the right or 

left to increase or decrease the temperature.

5.  Press the Command dial (

) to confirm the 

new temperature.

6.  Press the Back button (

) to return to normal 

operation mode, or rotate the Command dial  
(

) to adjust other operation conditions.

You can adjust the temperature while the display is 
flashing. Once the display stops flashing, the current 
temperature setting is stored.

Note

 

Ɣ

Take note of the original DHW 
temperature in case you want to 
restore it to the default. 

 

Ɣ

The DHW temperature range is 86°F 
(30°C) to 140°F (60°C) with 120°F as 
the default setting.

 

Ɣ

The boiler will retain your settings 
during a power outage.

5.  Press the Back button (

) to return to normal 

operation mode, or rotate the Command dial  
(

) to adjust other operation conditions.

You can adjust the temperature while the 
highlighted section is flashing. Once the flashing 
stops, the current temperature setting is stored.

Note

 

Ɣ

The space heating temperature 
cannot be adjusted when the Outdoor 
Reset Control is used.

 

Ɣ

In case of outdoor reset sensor 
malfunction, the boiler will operate at 
this set temperature.

 

Ɣ

Take note of the original heating 
temperature in case you want to 
restore it to the default.

 

Ɣ

The default space heating supply 
water temperature range is 104°F 
(40°C, Absolute MIN) to 180°F (82°C, 
Absolute MAX).

 

Ɣ

The default space heating return 
water temperature range is 86°F 
(30°C, Absolute MIN) to 149°F (65°C, 
Absolute MAX).

 

Ɣ

You can adjust the temperature ranges 
in the parameter settings menu.

 

Ɣ

The boiler will retain your settings 
during a power outage.

3.2.2    Adjusting the DHW Temperature

To adjust the water temperature:

1.  In normal operation mode, rotate the Command 

dial (

). The space heating temperature (

) is 

highlighted on the screen.

Summary of Contents for NFC-250/200H






























Reviews: