Page 3-26
Vector-LP Radio Beacon Transmitter Technical Instruction Manual
Issue 1.1
Section 3 Operating Instructions
x
DC Disconnect Level (
DC
power source
operation): if the dc power source is
below this voltage, the transmitter will
discontinue operation
x
DC Reconnect Level (
DC
power source
operation): when the dc power source
recovers to this voltage, the transmitter
will attempt to restore operation.
x
Requested Power Source:
AC
,
DC
,
BOTH
(if both ac and dc power sources
are installed) or
NONE
.
(c) Press
Done
to activate. A message
appears to confirm saving changes to the
EEPROM. Press
Yes
or
No
.
(d) The remaining parameters are for
monitoring only.
x
DC I/F Instld: Yes or No (indicates if
battery boost assembly A16 is installed).
x
Active Power Source: indicates the power
source configuration for the transmitter
(
AC
,
DC
,
BOTH
or
NONE
)
3.6.10 Configuring the Sonalert
Configure the status of the audible alarm
(sonalert) for all transmitter alarms as follows:
(a) From the main menu, highlight
Settings
(using
f
and
g
) and press
Select
.
Highlight
Configure Sonalert
and press
Select
.
NOTE
The Sonalert peripheral must be activated
(see 3.6.13.5) before settings in this section
can take effect.
(b) A list of transmitter alarms and their
current SonAlert (audible) and Site Ctrl
(remote outputs) status is displayed.
x
To configure an alarm for the sonalert,
use
f
and
g
to select the desired alarm;
press
Toggle
to change the status to
ON
.
x
Press
Modify
to configure an alarm for
use with site interface PWB A4 (if
installed). Use
f
and
g
to select the
desired alarm and press
Toggle
to
change the status from OFF to the
appropriate remote control output (
1
through
16
).
3.6.11 Setting a Timed Shutdown
Modify timed shutdown parameters as
follows:
Select
Meters
12:43:16 Power: 0W Side A Bypass
Main Menu
Changeover Control
Events Log
Settings
Peripherals
RCMS Settings
Vector NDB
rev 1. 0. 4. 1
Jul 27 2007
13:52:45
Nautel
Select
Meters
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Main Menu
Changeover Control
Events Log
Settings
Peripherals
RCMS Settings
Vector NDB
rev 1. 0. 4. 1
Jul 27 2007
13:52:45
Nautel
Select
Meters
12:43:16 Power: 0W Side A Bypass
Main Menu
Changeover Control
Events Log
Settings
Peripherals
RCMS Settings
Vector NDB
rev 1. 0. 4. 1
Jul 27 2007
13:52:45
Nautel
Select
Meters
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Main Menu
Changeover Control
Events Log
Settings
Peripherals
RCMS Settings
Vector NDB
rev 1. 0. 4. 1
Jul 27 2007
13:52:45
Nautel
Settings
Set Real Time Clock
Monitor Settings
Meter Settings
Power Source Select
Configure Sonalert
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
Settings
Set Real Time Clock
Monitor Settings
Meter Settings
Power Source Select
Configure Sonalert
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Settings
Meter Settings
Power Source Select
Configure Sonalert
Timed Shutdown
Factory Settings
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
Settings
Meter Settings
Power Source Select
Configure Sonalert
Timed Shutdown
Factory Settings
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Toggle
Modify
Back
12:43:16 Power: 0W Side A Bypass
Alarm Signal
SonAlert
SiteCtrl
PDM Latch B
OFF
OFF
PDM Latch A
OFF
OFF
High RF Curr
OFF
OFF
SWR Shutback
OFF
OFF
Low AC Voltage
OFF
OFF
Toggle
Modify
Back
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Alarm Signal
SonAlert
SiteCtrl
PDM Latch B
OFF
OFF
PDM Latch A
OFF
OFF
High RF Curr
OFF
OFF
SWR Shutback
OFF
OFF
Low AC Voltage
OFF
OFF
