Page 3-24
Vector-LP Radio Beacon Transmitter Technical Instruction Manual
Issue 1.1
Section 3 Operating Instructions
x
The first two values in each column are
internal tone generator reference values.
x
The third and fourth values are the
modulation depth (in %) for PTT Inactive
and PTT Active respectively.
x
Press
Toggle
to switch between
RF
Mon: CURR
and
Rf Mon: VOLT
, if
desired.
(j) Press
Compute New Thresholds
to
establish new monitor modulation %
thresholds.
(k) If a modification is made, a screen
appears which prompts you to save
changes to EEPROM. Select
Yes
or
No
.
3.6.8 Meter Settings
Determine the parameter to be displayed on
the front panel analog meter or the diagnostic
display’s meters screen as follows:
(a) From the main menu, highlight
Settings
(using
f
and
g
) and press
Select
.
Highlight
Meter Settings
and press
Select
. Use
f
and
g
to highlight
Change Meter Groups
,
Select Analog
Meter
or
Calib. Analog Meter
and press
Select
. Refer to the appropriate
paragraph (3.6.8.1 through 3.6.8.3 for
further details.
3.6.8.1 Changing Meter Groups
For monitoring and troubleshooting
convenience, the currently displayed meters
on the GUI’s meters screen can be changed
to display any three of the available meters:
Forward Power
+5 V P/S
Reflected Power
-15 V P/S
Modulation %
PDM A or B
Modulation % A or B
B+ Volts P/S A or B
VSWR
PA Volts P/S A or B
Ac Voltage
Dc Current P/S A or B
RF Current
Temperature P/S A or B
Antenna Current
Fan 1 Speed P/S A or B
Temperature
Fan 2 Speed P/S A or B
ATU Temperature
Battery Voltage
+24 V P/S
Battery Current
+15 V P/S
Charger Current
NOTE
Modulation % A and B refers to the
modulation read by monitor board A and B
respectively. Modulation % refers to the
active monitor board.
Set up the displayed parameters as follows:
(a) Use
f
and
g
to select the parameter to
be replaced and press
Modify
. Use
f
and
g
to select the desired parameter to
be monitored in its place. Press
Done
to
activate the change. Press
Back
.
(b) A message appears to confirm saving
changes to the EEPROM. Press
Yes
or
No
.
Forward Power: 0W
0
600
1200
Reflec. Power: 0.0W
0
100
200
VSWR: 1.00
0
1
2
12:43:16 Power: 0W Side A Bypass
Save Backup
Modify
Back
Forward Power: 0W
0
600
1200
Reflec. Power: 0.0W
0
100
200
VSWR: 1.00
0
1
2
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Save Backup
Modify
Back
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
Meter Settings
Change Meter Groups
Select Analog Meter
Calib. Analog Meter
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Meter Settings
Change Meter Groups
Select Analog Meter
Calib. Analog Meter
Select
Meters
12:43:16 Power: 0W Side A Bypass
Main Menu
Changeover Control
Events Log
Settings
Peripherals
RCMS Settings
Vector NDB
rev 1. 0. 4. 1
Jul 27 2007
13:52:45
Nautel
Select
Meters
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
Main Menu
Changeover Control
Events Log
Settings
Peripherals
RCMS Settings
Vector NDB
rev 1. 0. 4. 1
Jul 27 2007
13:52:45
Nautel
Settings
Set Real Time Clock
Monitor Settings
Meter Settings
Power Source Select
Configure Sonalert
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
Settings
Set Real Time Clock
Monitor Settings
Meter Settings
Power Source Select
Configure Sonalert
Main Menu
Select
Back
12:43:16 Power: 0W Side A Bypass
12:43:16 Power: 0W Side A Bypass
