manualshive.com logo in svg

National Instruments VXI-AO-48XDC, User Manual, Page: 27 / 58

Share
Download
National Instruments VXI-AO-48XDC User Manual Download Page 27

Chapter 3

Signal Connections

©

 National Instruments Corporation

3-9

VXI-AO-48XDC User Manual

Power Connections

Pin C1 of both I/O connectors is connected to the +5 V supply from the 
VXIbus power supply. These pins are referenced to GND and can supply 
power to external circuitry. The +5 V supply has a total of 2 A available. 
However, you must limit the current through each connector pin to 1.0 A.

The +5 V power supply has a self-resetting protection circuit breaker in 
series. If the circuit breaker protection is activated, simply remove the 
circuit causing the heavy current load and the circuit breaker will reset 
itself. For more information on these output pins, see the 

Digital I/O

 and 

Power Requirement

 sections in Appendix A, 

Specifications

.

Power rating

1.0 A per pin at +5 V ±10%,
+4.55 to +5.25 VDC at 1 A per pin

Warning

Under no circumstances should you connect these +5 V power pins directly to 
ground or to any other voltage source on the VXI-AO-48XDC or any other device. 
Doing so can damage the VXI-AO-48XDC and your VXIbus system. National 
Instruments is 

not

 liable for damage resulting from such a connection.

Summary of Contents for VXI-AO-48XDC



























































Reviews:

No comments