National Instruments VXI-AO-48XDC User Manual Download Page 17 | Manualshive

Page: 17 / 58

National Instruments VXI-AO-48XDC User Manual Download Page 17

Chapter 2

Configuration and Installation

VXI-AO-48XDC User Manual

2-4

©

National Instruments Corporation

Figure 2-2 shows switch settings for logical addresses hex 5 and C0.

Figure 2-2.

Logical Address Selection

Hardware Installation

This section contains general installation instructions for the
VXI-AO-48XDC. Consult your VXIbus mainframe user manual or
technical reference manual for specific instructions and warnings.

1.

Plug in your mainframe before installing the VXI-AO-48XDC.
The power cord grounds the mainframe and protects it from
electrical damage while you are installing the module. Do

not

turn on the mainframe.

P1 Connector

U51

VXI-AO-48XDC Module

1 2 3 4 5 6 7 8

Logical Address

Switch

Push up for logic 1

Push down for logic 0

a. Switch Set to Logical Address Hex 5 (Default)

1 2 3 4 5 6 7 8

Logical Address

Switch

Push up for logic 1

Push down for logic 0

b. Switch Set to Logical Address Hex C0

LSB

MSB

MSB

LSB

P1 Connector

U51

VXI-AO-48XDC Module

«
...
15
16
17
18
19
...
»

Summary of Contents for VXI-AO-48XDC



























































Reviews:

No comments