National Instruments VXI-AO-48XDC User Manual Download Page 7 | Manualshive

Page: 7 / 58

National Instruments VXI-AO-48XDC User Manual Download Page 7

©

National Instruments Corporation

ix

VXI-AO-48XDC User Manual

About This Manual

This manual describes the mechanical and electrical aspects of the
VXI-AO-48XDC and contains information concerning its configuration,
installation, and operation. The VXI-AO-48XDC is designed for precise
DC setpoint applications and provides general purpose digital I/O.

How To Use the Manual Set

The

VXI-AO-48XDC User Manual

is one piece of the documentation set

for your VXI data acquisition (VXI-DAQ) system. You could have any of
several types of documentation, depending on the hardware and software in
your system. Use the different types of documentation you have as follows:

•

Your VXI-DAQ hardware documentation—These documents have
detailed information about the VXI-DAQ hardware that plugs into or
is connected to your computer. Use these documents for hardware
installation and configuration instructions, specification information
about your VXI-DAQ hardware, and application hints.

•

Software documentation—You may have both application software
and driver software documentation. National Instruments application
software includes ComponentWorks, LabVIEW, LabWindows/CVI,
Measure, and VirtualBench. National Instruments driver software
includes NI-DAQ and VXI

plug&play

instrument drivers. After you

set up your hardware system, use either your application or driver
software documentation to help you write your application. If you have
a large, complicated system, it is worthwhile to look through the
software documentation before you configure your hardware.

•

Accessory installation guides or manuals—If you are using accessory
products, read the terminal block and cable assembly installation
guides or accessory board user manuals. They explain how to
physically connect the relevant pieces of the system. Consult these
guides when you are making your connections.

«
...
5
6
7
8
9
...
»

Summary of Contents for VXI-AO-48XDC



























































Reviews:

No comments