manualshive.com logo in svg

National Instruments VXI-AO-48XDC, User Manual, Page: 18 / 58

Share
Download
National Instruments VXI-AO-48XDC User Manual Download Page 18

Chapter 2

Configuration and Installation

©

 National Instruments Corporation

2-5

VXI-AO-48XDC User Manual

Warning

To protect both yourself and the mainframe from electrical hazards, do 

not

 turn 

on the mainframe until you are finished installing the VXI-AO-48XDC module.

2.

Remove or open any doors or covers blocking access to the mainframe 
slots.

3.

If you are installing the VXI-AO-48XDC into a D-size mainframe, 
first install an appropriate support for C-size modules.

4.

Insert the VXI-AO-48XDC in the slot you have selected:

a.

Align the top and bottom of the module with the card-edge guides 
inside the mainframe. 

b.

Slowly push the VXI-AO-48XDC straight into the slot until its 
plug connectors rest on the backplane receptacle connectors. 

c.

Using evenly distributed pressure, slowly press the 
VXI-AO-48XDC straight in until it seats in the expansion slot. 

d.

Make sure the front panel of the VXI-AO-48XDC is even with the 
front panel of the mainframe. 

5.

Tighten the retaining screws on the top and bottom edges of the front 
panel.

6.

Replace or close any doors or covers to the mainframe.

Software Installation 

If you are using a VXI

plug&play

 instrument driver, follow the instructions 

in the Setup Utility on the diskettes that were included with your VXI-DAQ 
hardware. This user manual assumes that the VISA software is installed. If 
VISA is not installed, you must get the VISA software from the supplier of 
your VXIbus controller.

If you are using NI-DAQ, refer to your release notes. Find the installation 
section for your operating system and follow the instructions given there.

If you are using ComponentWorks, LabVIEW, LabWindows/CVI, or 
VirtualBench, refer to the appropriate release notes to install your 
application software. After you have installed your application software, 
refer to the NI-DAQ release notes and follow the instructions given there 
for your operating system and application software.

Summary of Contents for VXI-AO-48XDC



























































Reviews:

No comments