background image

Figure 2. System Level Connection, Typical

1

2

Safety Interlock Connector

Test Fixture Enclosure

Operator Access Door

Mechanical Detection Switches

Mechanical detection switch is actuated

by operator access point

3

4

1. Safety Interlock Input
2. Safety Interlock Ground

3. Safety Interlock Pass Thru - Input
4. Safety Interlock Pass Thru - Ground

Related Information

Fore more information about the Safety Interlock, refer to the NI DC Power Supplies and
SMUs Help.
Testing the Safety Interlock

 on page 13

Mechanical Detection Switch Recommendations

Use high-reliability, fail-safe, normally open mechanical detection switches on all access
points to the test fixture enclosure.

Use two normally open switches wired in series so that a single switch failure does not
compromise safety protections.

Isolate switches so the operator cannot trigger or bypass the switches without the use of a
tool.

Ensure the switches' certifications meet your test application requirements. NI
recommends UL-certified safety switches to ensure reliability.

Install the switches in accordance with the switch manufacturer specifications.

Test the switches periodically to ensure proper implementation and reliability.

Safety Guidelines for System Operation

Caution

 

Hazardous voltages of up to the maximum voltage of the PXIe-4135 may

appear at the output terminals if the safety interlock terminal is closed. Open the
safety interlock terminal when the output connections are accessible. With the safety
interlock terminal open, the output voltage level/limit is limited to ±40 V DC, and

PXIe-4135 Getting Started Guide

  | 

© National Instruments

  | 

7

Summary of Contents for PXIe-4135



















Reviews: