National Instruments NI PXIe-8130 User Manual Download | Manualshive

Page: 55 / 84

background image

Chapter 3

I/O Information

NI PXIe-8130 User Manual

3-14

ni.com

ExpressCard/34 Slot

The NI PXIe-8130 controller is equipped with an ExpressCard/34 slot on
the front panel, which provides I/O expansion and options for removable
storage.

Figure 3-9 shows the location and pinouts for the ExpressCard/34 slot on
the NI PXIe-8130. Table 3-10 lists and describes the ExpressCard
connector signals.

Figure 3-9.

ExpressCard/34 Slot Location and Pinout

Table 3-10.

ExpressCard Connector Signals

Pin

Signal Name

Signal Description

1

GND

Ground

2

USBD–

USB Data –

3

USBD+

USB Data +

4

CPUSB#

USB Presence

5

RESERVED

Reserved by spec for future use

6

RESERVED

Reserved by spec for future use

7

SMBCLK

SMBus Clock

ExpressCard/34

Slot

1

26

«
...
53
54
55
56
57
...
»

Summary of Contents for NI PXIe-8130





















































































Reviews:

No comments

Related manuals for NI PXIe-8130

Brand: National Instruments Pages: 5

Brand: National Instruments Pages: 76

Brand: Qualys Pages: 2

Brand: Delta Pages: 2

Brand: Supermicro Pages: 16

Brand: NC-link Pages: 20

Brand: H3C Pages: 34

Brand: Camozzi Pages: 22

Brand: A4Tech Pages: 8

Brand: IBM Pages: 78

Brand: iTON Pages: 12

Brand: AMD Pages: 10

Database Appliance X6-2-HA

Brand: Oracle Pages: 473

IntelliStripe 65

Brand: Magtek Pages: 44

Brand: Radionics Pages: 100

COM600 series 5.1

Brand: ABB Pages: 42

Brand: LiveAction Pages: 2

Brand: NEC Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands