National Instruments NI PXIe-8130 User Manual Download | Manualshive

Page: 34 / 84

background image

Chapter 2

Installation and Configuration

NI PXIe-8130 User Manual

2-18

ni.com

LabVIEW RT Configuration Switches

Use the LabVIEW RT configuration switches to configure LabVIEW RT
if it is installed on the controller. If you are not using LabVIEW RT, these
switches should remain in the OFF position. The controller reads these
switches only after a system reset. You must reboot the controller for any
changes to take place.

The NI PXIe-8130 controller includes the following LabVIEW RT
configuration switches:

•

Switch 1

—

Boot LabVIEW RT

: Set this switch to ON to boot

LabVIEW RT.

Note

Booting LabVIEW RT requires that your NI PXIe-8130 controller has an IDE

(PATA) hard drive. Such a controller may be ordered from National Instruments with the
part number 780032-33.

•

Switch 2

—

Boot Safe Mode

: Set this switch to ON to boot LabVIEW

RT into safe mode to reconfigure TCP/IP settings and to download or
update software from a host computer. This switch overrides the
behavior of Switch 1. Booting the controller into safe mode does not
start the embedded LabVIEW RT engine. After changing the settings
or software, reboot the controller with this switch OFF to resume
normal operation.

•

Switch 3

—

Disable Startup VI

: Set this switch to ON to prevent VIs

from automatically running at startup if the controller becomes
inaccessible because of a startup VI.

•

Switch 4

—

Reset IP Address

: Set this switch to ON to reset the

IP address to

0.0.0.0

and other TCP/IP settings to their defaults. Use

this switch if moving the controller to a different subnet or if the
current TCP/IP settings are invalid.

«
...
32
33
34
35
36
...
»

Summary of Contents for NI PXIe-8130





















































































Reviews:

No comments

Related manuals for NI PXIe-8130

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

Brand: D-Link Pages: 4

Brand: GE Pages: 4

Brand: Accusys Pages: 34

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

NI WLS/ENET-9163

Brand: National Instruments Pages: 36

Momentum ROG Strix X570-E D-RGB

Brand: EK-Quantum Pages: 10

Brand: Z3 Technology Pages: 67

Brand: Xantech Pages: 4

Brand: Acromag Pages: 23

Brand: Top Pages: 21

Brand: IEI Technology Pages: 116

VXC-114U Series

Brand: ICP DAS USA Pages: 8

Brand: Allied Telesis Pages: 44

Brand: X-Micro Pages: 24

Brand: OPTO 22 Pages: 28

Audio Plus 3200

Brand: Zoltrix Pages: 34

Brand: Cabletron Systems Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands