manualshive.com logo in svg

National Instruments NI PXIe-8130, User Manual

Share
Download
National Instruments NI PXIe-8130 User Manual Download Page 58

©

 National Instruments Corporation

4-1

NI PXIe-8130 User Manual

4

Common Configuration 
Questions

This chapter answers common configuration questions you may have when 
using a NI PXIe-8130 embedded controller.

General Questions

What do the LEDs on the NI PXIe-8130 front panel mean?

Refer to the LED status descriptions in the 

Front Panel Features

 section of 

Chapter 3, 

I/O Information

.

After shutting down my NI PXIe-8130 controller, the Ethernet LEDs 
continue to blink. Is it safe to remove my controller or disconnect 
power?

The NI PXIe-8130 controller Ethernet device remains powered even after 
shutdown. It is safe to remove your controller or disconnect power.

How do I check the configuration of the memory, hard drive, 
time/date, and so on?

You can view these parameters in the BIOS setup. To enter the BIOS setup, 
reboot the NI PXIe-8130 and press <Delete> during the memory tests. 
Refer to the 

Accessing the BIOS Setup Utility

 section of Chapter 2, 

Installation and Configuration

, for more information.

Can I use the internal Serial ATA drive and an external hard drive at 
the same time?

Yes. Refer to the 

BIOS Setup Utility

 section of Chapter 2, 

Installation and 

Configuration

, for more information.

Summary of Contents for NI PXIe-8130





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands