National Instruments FieldPoint cFP-20 Series User Manual Download

Page: 74 / 76

Index

cFP-20xx and cFP-BP-x User Manual

I-4

ni.com

MAX

configuration, 2-18
installation, 2-18

100 Mbps LED, 3-4
memory specifications, B-1
modular jack connector

pin descriptions (table), 3-8
pin locations (figure), 3-8

modules.

See

cFP-20

hardware;

I/O modules

mounting hardware in rack

See also

installation, mounting hardware

in rack

mounting backplane, 2-8
rack-mount accessory, 2-8

figures, 2-9

mounting hardware on DIN rail.

See

installation, mounting hardware on DIN rail

mounting hardware to panel.

See

installation,

mounting hardware to panel

National Instruments support and

services, C-1

network specifications, B-1
network watchdog, 3-1

OPC client, 5-2
OPC server, 5-2
overview

cFP-20

hardware, 1-1

FieldPoint software, 1-3
setup, 1-3
using cFP-20

from host

applications, 5-1

panel mount.

See

installation, mounting

hardware on panel

physical characteristic specifications, B-3
pin descriptions

DB-9

connector pin descriptions

(table), 3-7

connector pin locations

(figure), 3-7

pollution degree, 2-3
power connections

wiring, 2-16

power connector, 1-2, 2 -5, 2-1 3, 3 -10
POWER LED, 3-3
power requirements specifications, B-2
power supply, 2-16
power-on self test (POST), 2-17, 3 -4
power-up

launching LabVIEW RT applications at

system startup, 4-6, 4 -11

overview, 2-17
runaway startup applications, A-1

power-up states, configurable, 3-2
programming examples (NI resources), C-1

rack mount.

See

installation, mounting

hardware in rack

rail clip, 1-2, 2-5, 2 -11, 2-13
registering computers

with OPC, 5-2

removable compact flash, 3-11
RESET IP switch, 3-6
resetting a FieldPoint bank, 3-6
RS-232 serial port, 1-1, 2-5, 2 -13, 3-6, 5 -6
RS-485 serial port, 3-6

Summary of Contents for FieldPoint cFP-20 Series













































































Search results

Summary of Contents for FieldPoint cFP-20 Series

Reviews:

Related manuals for FieldPoint cFP-20 Series

Brands by name

Popular brands

National Instruments FieldPoint cFP-20 Series, User Manual

Search results

Summary of Contents for FieldPoint cFP-20 Series

Reviews:

Related manuals for FieldPoint cFP-20 Series

Brands by name

Popular brands