manualshive.com logo in svg

National Instruments FieldPoint cFP-20 Series, User Manual

Share
Download
National Instruments FieldPoint cFP-20 Series User Manual Download Page 6

©

 National Instruments Corporation

v

cFP-20xx and cFP-BP-x User Manual

Contents

Chapter 1
Overview of Compact FieldPoint

cFP-20

xx

 Compact FieldPoint Controller Overview .....................................................1-1

FieldPoint Software Overview.......................................................................................1-3
cFP-20

xx

 Setup Overview .............................................................................................1-3

Chapter 2
Installing Compact FieldPoint Hardware and Software

What You Need to Get Started ......................................................................................2-1
Compact FieldPoint Safety Information ........................................................................2-2
Mounting the Compact FieldPoint Backplane...............................................................2-4

Mounting the Backplane on a Panel ................................................................2-6
Mounting the Backplane in a Standard 19-in. Rack........................................2-8

Installing a DIN Rail in the Rack-Mount Accessory ........................2-10

Mounting the cFP-BP-4 on a DIN Rail ...........................................................2-11

Installing the cFP-20

xx

 Controller on a Compact FieldPoint Backplane ......................2-12

Installing I/O Modules on the Backplane ......................................................................2-13
Connecting to Field Devices..........................................................................................2-14
Installing Connector Blocks on the Backplane..............................................................2-15
Connecting the cFP-20

xx

 to a Network .........................................................................2-16

Wiring Power to the Compact FieldPoint System .........................................................2-16
Powering Up the cFP-20

xx

............................................................................................2-17

Installing Software on the Host PC................................................................................2-18
Configuring the Compact FieldPoint System in MAX..................................................2-18

Chapter 3
Feature Descriptions

Guarding against Network Failures (Network Watchdog) ............................................3-1
Guarding against Other System Failures (Hardware Watchdog) ..................................3-1
Storing a Custom Power-Up Configuration...................................................................3-2

Setting a Power-Up State with the Snapshot Feature ......................................3-2
Configurable Power-Up States ........................................................................3-2

Inserting, Removing, and Replacing I/O Modules ........................................................3-2
LED Indicators...............................................................................................................3-3

POWER LED ..................................................................................................3-3
STATUS LED .................................................................................................3-3

Summary of Contents for FieldPoint cFP-20 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands