National Instruments FieldPoint cFP-20 Series User Manual Download

Page: 12 / 76

Chapter 1

Overview of Compact FieldPoint

cFP-20xx and cFP-BP-x User Manual

1-4

ni.com

Install software as described in Chapter 2,

Installing Compact

FieldPoint Hardware and Software

Install programming software (LabVIEW RT).

Install FieldPoint software.

Configure Compact FieldPoint system and verify configuration as
described in the

Measurement & Automation Explorer Help for

FieldPoint

Configure cFP-20

network settings.

Configure I/O module ranges and settings.

Configure security.

Connect input signals and loads to I/O modules.

Test channels.

Save settings.

Configure optional settings as described in Chapter 3,

Feature

Descriptions

Develop application as described in Chapter 4,

LabVIEW RT

Programming

Launch LabVIEW RT.

Build basic application.

Switch execution target to test application on cFP-20

Embed application by building

.exe

with LabVIEW RT targeted

to cFP-20

Test embedded application.

Deploy system.

Summary of Contents for FieldPoint cFP-20 Series













































































Search results

Summary of Contents for FieldPoint cFP-20 Series

Reviews:

Related manuals for FieldPoint cFP-20 Series

Brands by name

Popular brands

National Instruments FieldPoint cFP-20 Series, User Manual

Search results

Summary of Contents for FieldPoint cFP-20 Series

Reviews:

Related manuals for FieldPoint cFP-20 Series

Brands by name

Popular brands