manualshive.com logo in svg

National Flooring Equipment PANTHER 8274, Instruction Manual

Share
Download
National Flooring Equipment PANTHER 8274 Instruction Manual Download Page 27

Page 26

MAINTENANCE

A well-maintained machine is a productive machine. If not properly maintained, it could be unsafe and
could break down. A scheduled maintenance program should insure a long system life and a safe work
environment. 

1. Always wear eye protection. 

2. Keep flammable and fragile objects away from the tool. 

3. Always check nuts and bolts to make sure they are tight. 

4. Always use the tool with proper voltage specified on the machine's nameplate. 

5. Always keep guards in place. 

6. Do not operate around water or wet conditions without use of GFI on cord. 

7. Use properly grounded cord and receptacle. 

8. Unplug from power before servicing. 

9. Use 12 gauge or heavier wire cord, not exceeding 50 feet in length. 

10. Do not force machine. 

11. Do not alter machine. 

12. Keep wheels free from debris. 

13. Maintain Labels. These carry important information. If unreadable or missing, contact National for a

free replacement.

MAINTAINING TOOLS

Keep in good repair by adopting a regular maintenance program. Before use, examine the general
condition. Inspect guards, switches, tool cord set and extension cord for damage. Check for loose
screws, misalignment, binding of moving parts, improper mounting, broken parts and any other condition
that may affect its safe operation. If abnormal noise or vibration occurs, turn the tool off immediately and
have the problem corrected before further use. Tag damaged tool, “DO NOT USE” until repaired (See
Repairs). 

• Mechanical inspection and cleaning (pulleys, belts, bearings, nuts, bolts, housing, labels, etc.).

• Electrical inspection (switch, cord, plugs, etc.).

• Testing to assure proper mechanical and electrical operation.

8274/9274 MAINTENANCE

WARNING

: DO NOT lock switch on handle into a permanent on position. If operator would lose

control or be disabled, machine continues to operate.

WARNING

: To reduce the risk of injury, always unplug your tool before performing any

maintenance. Never disassemble the tool or try to do any rewiring on the tool’s electrical system.
Contact National for ALL repairs.

Summary of Contents for PANTHER 8274


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands