National Flooring Equipment PANTHER 8274 Instruction Manual Download Page 20

Page: 20 / 49

Page 20

8274/9274 PROCEDURE

Start:

Press Start Button

Stop:

Press Stop Button

Change Direction:

Press Fwd/Rev Button then Enter

Button

Change Speed:

Up Arrow = Faster,

Down Arrow = Slower

ONCE POWER IS APPLIED TO DRIVE

(This will usually mean the unit is plugged in) the display will appear

similar to this:

TOP

NORMALLY THE FREQUENCY IS PRE-SET TO 50 OR 60 HZ

. The exception: last operating speed is

displayed in HZ

PRESS START

- Motor will start to turn. Full speed will be achieved in 20 seconds.

If motor is running wrong direction

- Press FWD/REV button on keypad. Then

press “enter” button

within 3 seconds

TO CHANGE SPEED

- Press the up arrow to increase speed (up to a factory preset maximum). Press Down

Arrow button to decrease speed

PRESS STOP -

to stop running motor

MACHINE START UP PROCEDURE

TO RUN MACHINE

1. Connect machine to power source.

2. Attach tether cord to both operator and machine

(Figure A). Failure to do so could cause damage to
property and/or machine.

3. Securely hold handle with one hand.

Note: Applying light pressure downward on the handle
takes pressure off the head of the machine.

4. Turn switch to “on” position (Figure B).

Note: Machine is programmed with a slow start.

LUE

IGHTS

: E

NABLE

READY TO RUN

IGHTS

: D

EFAULT

(

SEE TROUBLESHOOTING

ERROR CODES

)

Enter

Fwd/Rev

Start

Stop

Down Arrow

(Decreases Speed)

Up Arrow

(Increases Speed)

Figure A

tether cord

attached

NOTE: Once machine is running, keep it on “load mode”. Always be aware that the load does not go
over 100%.

Summary of Contents for PANTHER 8274


















































Search results

Summary of Contents for PANTHER 8274

Reviews:

Brands by name

Popular brands

National Flooring Equipment PANTHER 8274, Instruction Manual

Search results

Summary of Contents for PANTHER 8274

Reviews:

Brands by name

Popular brands