manualshive.com logo in svg

National Flooring Equipment PANTHER 8274, Instruction Manual

Share
Download
National Flooring Equipment PANTHER 8274 Instruction Manual Download Page 12

Page 12

VACUUM PORT

8274/9274 PROCEDURE

Figure A

WARNING:

Make sure you are using the proper style of vacuum for what you are grinding,

scraping or sanding. Failure to do so could cause emissions of hazardous particulates or explosion
due to fine dust (ie, wood sanding), which is flammable. Make sure the system you are using complies
or exceeds OSHA recommended standard. Make sure the rubber dust guard is covering all the way to
the floor surface.

The machine is provided with a vacuum port at the rear of
the machine. Use a vacuum hose that snugly fits either on
the outside or the inside of the port. 

Connect vacuum hoses (Figure A).

Figure B

WEIGHTS

Weights rotate front to back.  To apply added weight to head, one or or both weights can be rotated
forward (Figure B).  To take load off machine, pull weights to the back (Figure C).  If load is over 100%,
pull weights back.  If circuit breakers blow, pull weights back.

Figure C

Summary of Contents for PANTHER 8274


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands