manualshive.com logo in svg

National Flooring Equipment PANTHER 8274, Instruction Manual

Share
Download
National Flooring Equipment PANTHER 8274 Instruction Manual Download Page 13

Page 13

Page 13

8274/9274 PROCEDURE

RUBBER DUST GUARD

ATTACHING

Return machine to upright position.  Attach dust guard (Figure A) keeping as close to the floor as
possible.  If dust is exposed when operating machine, stop machine and readjust dust guard.

POSITIONING

Unplug machine from power source. With machine sitting in the operating position, remove rubber dust
guard held on by Velcro. Starting at one end of the shroud, place guard to rest on floor surface. Firmly
press rubber guard into securing Velcro on shroud. Wrap rubber guard all the way around the shroud
making sure the guard rests on the floor surface and is secure.  Inspect for air gaps.

If rubber guard securing Velcro becomes loaded up with debris, wash out with mild soap or blow out with
an air hose. If Velcro on the machine is damaged or worn out, replace before using the machine. If the
rubber guard is cut, damaged or worn out, replace before using the machine. Safety glasses need to be
worn by operator and all people working around the equipment.

WARNING:

NEVER operate machine without rubber guard in place covering plate completely.

Failure to do so could cause serious injury.

NEVER mount or readjust rubber guard with machine plugged in. Disconnect from power source
before mounting or readjusting the rubber guard. 

Figure A

Summary of Contents for PANTHER 8274


















































Reviews:

No comments

Brands by name

Popular brands

Load more brands