8
5. When the configuration keypad powers up, its display will read "
XX OUT OF SYSTEM RCM MODULE
".
IMPORTANT:
After the display reads "
XX OUT OF SYSTEM
" , you MUST stop and wait for the IBR-ZREMOTE
components to reset and prepare for communication; only after the display changes to "
XX OUT OF SYSTEM
RCM
MODULE
" may you proceed with the next step (the words "
RCM-MODULE
" must be in the display text).
6. Press
1 1 1 2 3 FUNCTION
(or
MENU
) to enter Keypad Configuration Mode.
7. Tap
FUNCTION
(or
MENU
) repeatedly until the configuration keypad displays "
Keypad Address
".
8. Enter the correct address and tap
ON/OFF
(or
ENTER
) to save. (
Note:
The keypad address will not change until
you tap
ON/OFF
or
ENTER
).
9. Tap
FUNCTION
(or
MENU
) repeatedly until the keypad displays "
Keypad TYPE RP1CAE2
".
10. Tap
INTERIOR / STAY
or
NEXT
to toggle between the keypad model names. When selected, tap
ON/OFF
(or
ENTER
)
to save, then tap
RESET
to exit.
Note:
If using a Stay/Away keypad you
MUST
press and hold
STAY
to change the
keypad type. The keypad will then revert back to "
Keypad Beep ON
"; scroll to Keypad Type to verify it is set to "
K1CA
".
11. Return the control panel
CONFIG
jumper back to the top two pins ("
NORM
"). "System Ready" should appear on
the keypad if all zones are closed.
12. Disconnect the programming cable from the IBR-ZREMOTE and replace jumper
J4
that was removed in step 2.
USING AN APP TO CONFIGURE THE IBR-ZREMOTE
1. Install the iBridge APP on your Android, iPad or iPhone Device. Apps can be obtained from
Google Play
or the
Apple Store
.
2. Connect to the ISEE-WAP Wi-Fi access point "
IBRIDGE
" using the WEP key
1234567890
or connect your device to
the customers Wi-Fi Network to access the iBridge (verify that you are connected to the iBridge by launching the
APP, and your status should display "System Ready" or display the keypad status correctly).
3. Put the control panel into Keypad Configuration Mode by moving the configuration jumper to the bottom two pins
("
CONFIG
" ), located inside the control panel.
4. Using the iBridge app, at the Home screen tap "
SECURITY
" then "
OTHER OPTIONS
" and select "
KEYPAD
MODE
" . After putting the control panel into Keypad Configuration Mode, it normally takes up to 40 seconds
for the keypad on the iBridge APP to go "out of system". The keypad will display "
01 Out of System RCM
MODULE
".
IMPORTANT:
After the display reads "
XX OUT OF SYSTEM
" , you MUST stop and wait for the
IBR-ZREMOTE components to reset and prepare for communication; only after the display changes to "
XX OUT OF
SYSTEM
RCM MODULE
" may you proceed with the next step (the words "
RCM-MODULE
" must be in the
display text).
5. Press
1 1 1 2 3 FUNCTION
(
or MENU
) to enter Keypad Configuration Mode.
Note:
Do NOT change the Virtual
PBX, Account ID or Dealer ID.
6. Tap
FUNCTION
(or
MENU
) repeatedly until the configuration keypad displays "
Keypad Address
".
7. Enter the correct address and tap
ON/OFF
(or
ENTER
) to save. (
Note:
Keypad address will not change until you
tap
ON/OFF
or
ENTER
).
8. Tap
FUNCTION
(or
MENU
) repeatedly until the keypad displays "
Keypad TYPE RP1CAE2
".
9. Tap
INTERIOR / STAY
or
NEXT
to toggle between the keypad model names. When selected, tap
ON/OFF
or
ENTER
to save, then tap
RESET
to exit.
10. Return the control panel
CONFIG
jumper back to the top two pins ("
NORM
"). "System Ready" should appear on
the keypad if all zones are closed.
If you are using the IBR-ITAB wireless tablet and you are unable to connect with the IBR-ZREMOTE using the APP, then
the "
USING THE IBR-ITAB TO CONFIGURE THE IBR-ZREMOTE
" procedure (below) can be used.
USING THE IBR-ITAB TO CONFIGURE THE IBR-ZREMOTE
If step 4 was completed properly, the IBR-ZREMOTE and ISEE-WAP should have obtained IP addresses and be ready for
use. Power up an IBR-ITAB and it will connect to the ISEE-WAP and IBR-ZREMOTE automatically (this process may take
several minutes the first time it is performed). The top status bar will display "
System Ready
" or "
Not Ready to Arm
" when
it is ready for the following steps:
Set the keypad skin and configure the IBR-ITAB as follows:
1. On the IBR-ITAB:
a.
Press and hold
the
System Settings
"gear" icon (located at the lower left corner of the display) for 4 seconds.
b. Tap the empty field. In the keyboard, type the administrator password "
admin
".
c. Tap
Done
and then
OK
.
d. Tap
Yes
to the "Making System Changes…" popup to proceed.
2. Once in the Dealer Settings menu, tap
Security
.
Summary of Contents for iBridge Suite
Page 18: ...18 NOTES...