L
NAPCO Security Systems
Freedom F-64 Programming Instructions
Page 9
WI1502A 9/06
E
A
SY MEN
U
DR
IVEN
PRO
G
RA
M
MOD
E
Central Station Receiver 1 Telephone Number
•
Enter telephone number of up to 16 digits.
•
Press
1
through
9
for digits 1–9;
G
0
for a zero and
0
for a blank (•).
•
Press
G
1
through
G
5
for letters B–F, respectively.
•
Pre-Dial Delay = “D” (
G
4
); Dial-Tone Detection = “E” (
G
5
).
•
Press
U
to save and press the
NEXT/YES
button to proceed.
NOTE:
Central Station Receiver 2 and 3 Telephone Numbers must be entered in Direct Ad-
dress Programming.
See CS Receiver Options.
Central Station Receiver 1 Account Number
•
Enter an account number of up to four digits.
•
Press
0
through
9
for digits 0–9, and
G
0
for a blank (•).
•
Press
U
to save and press the
NEXT/YES
button to proceed.
NOTE:
Central Station Receiver 2 and 3 Account Numbers must be entered in Direct Ad-
dress Programming.
See CS Reporting Options.
Central Station Receiver 1 Format
•
From the table at the right enter the receiver format.
•
Press
0
through
9
, and
G0
for blank (•).
•
Press
G1
through
G4
for letters B–E.
•
Press
U
to save and press the
NEXT/YES
button to proceed.
Enter User Codes
(Press
R
to set cursor.)
For default program, enter up to 64 User Codes, with Area 1, 2, 3 & 4 Options.
•
Press the (
R
) button once to set the cursor to the User Code.
•
Press
0
through
9
to enter a code from 3 to 6 digits, leave blank (•) any trailing boxes.
•
Press
R
to set the cursor to the Area 1 Options Level. Refer to the table below for available
options. For Area 2 Options, press
R
once again. For Area 3 & 4 Options, press
R
a third
and fourth time.
•
If “Enable Global Ambush Code” (Address 1422) is enabled and “Global Ambush Code” (Address
2045) is
not
left blank (•),
do not
program the first two digits of ANY User Code the same as the
“Global Ambush Code”. See Address 2045 further in this manual for more information.
•
Press
U
to save.
Note:
Duplicate User Codes are not allowed; therefore a duplicate Code en-
tered in the LCD Window will erase when
U
is pressed. To proceed to the next User Code, press
R
to set the cursor to the User Number and change it using the number buttons. Press the
NEXT/YES
button to proceed.
(Direct Entry)
Centr al Phone #
(Direct Entry)
Central Station
Account # (____)
DATA
ENTRY
CS RECEIVER 1 FORMAT
•
(blank)
Ademco Slow, Silent Knight
Slow
2
Radionics Fast
3
Silent Knight Fast
4
Radionics, DCI, Franklin Slow
5
Universal High Speed
B
SIA
C
Ademco Point ID
E
Pager
(Direct Entry)
S e e W I f o r I n f o
R c v r F o r m a t ( 0 )
E n t e r u s e r c o d e - >
U 0 1 1 2 3 - 9 -
User# User Code Area 1 Area 2
Example:
Program a code of “2222” for user 02, with area 1 options of “Arm/
Disarm” and “User Program”. Enter “2222” for a user code,
“• (blank) 9” for area 1 options and “• (blank) •(blank)” for area 2 options.
USER AREA OPTIONS
DATA ENTRIES
L
R
blank(•)
blank(•)
Disabled
blank(•)
1
Arm/Disarm
blank(•)
2
Arm Only
blank(•)
3
Service
blank(•)
4
Access
blank(•)
5
Ambush
blank(•)
Add 8
* User Program
4
blank(•)
Bypass Enable
OPTION
ENABLED
USER OPTIONS
USER CODE
(UP TO 6 DIGITS)
AREA 1
OPTIONS
AREA 2
OPTIONS
AREA 3
OPTIONS
AREA 4
OPTIONS
